21
For both adjustments, do as follows.
1. Make sure that the tool is unplugged.
2. Draw the cutting line on the workpiece and place it
on the turn table. At this time, do not secure the
workpiece with a vise or similar securing device.
3. Lower the blade by lowering the handle and just
check to see where the cutting line and the position
of the saw blade is. (Decide which position to cut on
the line of cut.)
4. After decision the position to be cut, return the han-
dle to the original position. Secure the workpiece
with the vertical vise without shifting the workpiece
from the pre-checked position.
5. Plug the tool and turn on the laser switch.
6. Adjust the position of laser line as follows.
The position of laser line can be changed as the movable
range of the adjusting screw for the laser is changed by
turning two screws with a hex wrench. (The movable
range of laser line is factory adjusted within 1 mm from
the side surface of blade.)
To shift the laser line movable range further away from
the side surface of blade, turn the two screws counter-
clockwise after loosening the adjusting screw. Turn these
two screws clockwise to shift it closer to the side surface
of the blade after loosening the adjusting screw.
Refer to the section titled “Laser beam action” and adjust
the adjusting screw so that the cutting line on your work-
piece is aligned with the laser line.
NOTE:
• Check the position of laser line regularly for accuracy .
• Have the tool repaired by Makita authorized service
center for any failure on the laser unit.
Replacing fluorescent tube (Fig. 54)
For model LS0714F, LS0714FL
CAUTION:
• Always be sure that the tool is switched off and
unplugged before replacing the fluorescent tube.
• Do not apply force, impact or scratch to a fluorescent
tube, which can cause a glass of the fluorescent tube to
be broken resulting in a injury to you or your bystand-
ers.
• Leave the florescent tube for a while immediately after
a use of it and then replace it. If not, you may burn
yourself.
Remove screws, which secure Lamp Box for the light.
Pull out the Lamp Box keeping pushing lightly the upper
position of it as shown in the figure.
Pull out the fluorescent tube and then replace it with
Makita original new one.
Cleaning of the lens for the laser light
(Fig. 55 & 56)
For model LS0714FL, LS0714L
If the lens for the laser light becomes dirty, or sawdust
adheres to it in such a way that the laser line is no longer
easily visible, unplug the saw and remove and clean the
lens for the laser light carefully with a damp, soft cloth.
Do not use solvents or any petroleum-based cleaners on
the lens.
To remove the lens for the laser light, remove the saw
blade before removing the lens according to the instruc-
tions in the section titled “Installing or removing saw
blade”.
Loosen but do not remove the screw which secures the
lens using a screwdriver.
Pull out the lens as shown in the figure.
NOTE:
• If the lens does not come out, loosen the screw further
and pull out the lens again without removing the screw.
Replacing carbon brushes (Fig. 57 & 58)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
After use
• After use, wipe off chips and dust adhering to the tool
with a cloth or the like. Keep the blade guard clean
according to the directions in the previously covered
section titled “Blade guard”. Lubricate the sliding por-
tions with tool oil to prevent rust.
• When storing the tool, pull the carriage toward you fully
so that the slide pole is thoroughly inserted into the turn
base.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Carbide-tipped saw blades
• Vise assembly (Horizontal vise)
• Vertical vise
• Socket wrench 10
• Holder set
• Holder assembly
• Holder rod assembly
• Set plate
• Dust bag
• Triangular rule
• Lock-off button (2 pcs.)
• Fluorescent tube
• Hex wrench
