Manual Makita LH 1040 (page 14 of 116) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448578

Zoom out

Zoom in

1/116

ENE060-1

Intended use

The tool is intended for accurate straight cutting and

(only when used as a miter saw on the lower table) miter

cutting in wood.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future reference.

ENB088-5

TABLE TOP MITER SAW SAFETY WARNINGS

FOR BOTH MITER SAW MODE AND TABLE SAW

(BENCH SAW) MODE

1. Check the blade carefully for cracks or deforma-

tion before operation.

Replace damaged blade immediately.

2. Do not operate saw without guards and riving

knife in place, especially after a mode change.

Check blade guards for proper closing before

each use. Do not operate saw if blade guards do

not move freely and close instantly. Never clamp

or tie the blade guards into the open position.

Any irregular operation of the blade guards

should be corrected immediately.

3. Use only saw blades specified by the manufac-

turer and which conform to EN847-1. The groove

width of the cut must be thicker than the riving

knife and the blade body must be thinner than

the riving knife.

4. Do not use saw blades manufactured from high

speed steel.

5. Wear eye protection.

6. Wear hearing protection to reduce the risk of

hearing loss.

7. Wear gloves for handling saw blades (saw

blades shall be carried in a holder wherever

practicable) and rough material.

8. Connect the tool to a dust collecting device

when sawing.

9. Always store the push-stick when it is not in use.

10. Keep the floor area around the tool level well

maintained and free of loose materials e.g. chips

and cut-offs.

11. The operator is adequately trained in the use,

adjustment and operation of the tool.

12. Stop and unplug the saw when unattended.

13. To reduce the emitted noise, always be sure that

the blade is sharp and clean.

14. Use only saw blades that are marked with a max-

imum speed equal to or higher than the no load

speed marked on the tool.

15. When the tool is fitted with a laser or LED, do not

replace the laser or LED with a different type.

Ask an authorized service center for repair.

16. Never remove any cut-offs or other parts of the

workpiece from the cutting area whilst the tool is

running with an unguarded saw blade.

17. The tool should not be used for slotting, rebating

or grooving.

18. Before carrying the tool, always cover the upper

part of the saw blade by the top guard and

secure all moving portions. When lifting or car-

rying the tool, do not use the guard as a carrying

handle.

19. Clean and be careful not to damage the spindle,

flanges (especially the installing surface) and

hex bolt before or when installing the blade.

Damage to these parts could result in blade

breakage. Poor installation may cause vibration/

wobbling or slippage of the blade. Use only

flanges specified for this tool.

20. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive cut-off wheels may cause an injury.

21. Select the correct saw blade for the material to

be cut.

22. Do not cut metal objects such as nails and

screws. Inspect for and remove all nails, screws

and other foreign material from the workpiece

before operation.

23. Knock out any loose knots from workpiece

BEFORE beginning to cut.

24. Do not use the tool in the presence of flammable

liquids or gases.

25. For your safety, remove the chips, small pieces,

etc. from the work area and table top before

plugging the tool and starting operation.

26. Keep hands and make your bystander and your-

self position out of path of and not in line with

saw blade. Avoid contact with any coasting

blade. It can still cause severe injury and never

reach around saw blade.

27. Be alert at all times, especially during repetitive,

monotonous operations. Do not be lulled into a

false sense of security. Blades are extremely

unforgiving.

28. Make sure the shaft lock is released before the

switch is turned on.

29. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

30. Wait until the blade attains full speed before cut-

ting.

31. Stop operation immediately if you notice any-

thing abnormal.

32. Turn off tool and wait for saw blade to stop

before moving workpiece or changing settings.

33. Unplug tool before changing blade, servicing or

not in use.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LH 1040 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita LH 1040

Makita LH 1040 User Manual - English, Dutch - 31 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LH 1040 Manual

Product: