448571
11
Zoom out
Zoom in
Previous page
1/72
Next page
11
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
Due to our continuing program of research and development, the specifications herein are subject to change without notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
Symbols
END215-2
The following show the symbols used for the tool. Be sure that you
understand their meaning before use.
.......... Read instruction manual.
..........Withdraw the main plug.
..........Wear safety glasses.
.......... Do not place hand or fingers close to the blade.
..........Only for EU countries
Do not dispose of electric equipment together with
household waste material!
In observance of European Directive 2002/96/EC on
waste electrical and electronic equipment and its
implementation in accordance with national law,
electric equipment that have reached the end of their
life must be collected separately and returned to an
environmentally compatible recycling facility.
Intended use
The tool is intended for cutting in wood.
Power supply
The tool should be connected only to a power supply of the same
voltage as indicated on the nameplate, and can only be operated
on single-phase AC supply. They are double-insulated in
accordance with European Standard and can, therefore, also be
used from sockets without earth wire.
1. Wheel
2. Upper cover
3. Light switch
4. Switch
5. Rip fence
6. Lower cover
7. Carry Handle
8. Dust box
9. Knob (For tensioning blade)
10. Knob (For securing upper housing door)
11. Knob (For adjusting blade guide)
12. Knob (For securing blade guide)
13. Upper blade guide
14. Blade
15. Knob (For securing lower housing door)
16. Knob (For tensioning V-belt)
17. Driving belt
18. Stand
19. Tire
20. Lock lever (For securing table tilt)
21. Dust extraction port
22. (Quick release) lever
23. Knob (For adjusting cutter tool tracking)
24. Grip (For adjusting table tilt)
25. Frame
26. Handle
27. Washer
28. Hex socket head bolt
29. Plate spring
30. Securing hole
31. Position hole
32. Table
33. Hex bolts
34. Trunnion
35. Pin
36. Thumb screw
37. Guide rail
38. Switch cover
39. OFF switch
40. ON switch
41. ON
42. Push stick
43. Miter gauge
44. Lock handle
45. Knob
46. Knob (A)
47. Fence
48. Lock lever
49. Fence holder
50. Knob (B)
51. Hold-down clamp
52. Thumb screws
53. Dust cover
54. Saw blade
55. Saw housing
56. Lower blade guard
57. Quick release lever
58. Lower band saw wheel
59. Motor pulley
60. Driving belt
61. Pulley of the driving wheel
62. Approx. 10 mm
63. Lock knob
64. Adjusting knob
65. Guide bearing
66. Bolt A
67. Guide bearing distance from bottom of
blade
68. Bolt C
69. Bolt B
70. Bearing holder
71. Thrust bearing
72. Screw
73. Nut
74. Large opening collector
75. Small opening collector
76. Small dust collector (Mounted on main
unit)
77. Large dust collector (For changeover)
78. Rail
79. Shoulder
80. Hex bolt
Model LB1200F
Wheel size 305 mm
Max. cutting capacity 165 mm
No load speed
High 840 min
-1
(50 Hz)/1,040 min
-1
(60 Hz)
Low 420 min
-1
(50 Hz)/520 min
-1
(60 Hz)
Cutting speed
High 13.3 m/s (800 m/min) (50 Hz)/16.7 m/s (1,000 m/min) (60 Hz)
Low 6.7 m/s (400 m/min) (50 Hz)/8.3 m/s (500 m/min) (60 Hz)
Blade size Circumference 2,240 mm x Width 6 mm, 13 mm, 16 mm
Overall dimensions 615 mm x 775 mm x 1,600 mm
Table size 560 mm x 400 mm
Net weight 81.2 kg
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita LB 1200F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita LB 1200F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info