599023

Makita KR400MP Manual

6
Zoom out
Zoom in
Previous page
1/64
Next page
6
Inspecting the blades and protector
Check and clean the blades and protector daily. If they are worn,
bent and cracked, replace them.
Lubricating moving parts (Fig. 6)
NOTICE: Follow the instruction of the frequency and amount of
grease supplied. Otherwise insufcient lubrication may damage
moving parts.
Gear case:
Fill approx. 30 ml of grease (Shell Alvania S-1 or equivalent)
through the grease port (A) evenly every 50 hours of operation.
Drive axle (B):
Apply grease (Shell Alvania No.2 or equivalent) every 25 hours of
operation.
Overall inspection
Tighten loose bolts, nuts and screws.•
Check for damaged parts and blades. Ask Makita authorized •
service center to replace them.
Storage
WARNING: Follow the warnings and precautions in the chapter
“Safety precautions” and the instruction manual of the power unit.
(Fig. 7)
When storing the cultivator attachment separated from the power
unit, put the cap onto the end of the shaft.
Maintenance schedule
Operating hour Before Operation
Daily
(10 h)
25 h 50 h Corresponding page
Whole unit Visually inspect for
damaged parts
6
All xing screws and nuts Tighten
6
Blades and protector Clean and visually inspect
for damaged parts
6
Gear case Supply grease
6
Drive axle Supply grease
6
Power unit Refer to the instruction manual of the power unit
Troubleshooting
Problem Probable cause Solution
The motor does not start. Refer to the instruction manual of the power unit.
The motor stops soon after its start.
The maximum speed is limited.
The blades do not rotate.
Stop the motor immediately!
The blades are not installed properly. Install the blades properly.
Roots or the like are caught in the blades. Remove the foreign matter.
The drive system does not work properly. Ask Makita authorized service center to
inspect and repair it.
The unit vibrates abnormally.
Stop the motor immediately!
The blades are not installed properly. Install the blades properly.
The drive system does not work properly. Ask Makita authorized service center to
inspect and repair it.
The blades do not stop.
Stop the motor immediately!
The power unit does not work properly. Refer to the instruction manual of the power
unit.
Technical data
Model KR400MP
Dimensions (L x W x H) mm 965 x 235 x 264
Mass kg 2.9
Cultivating width mm 160
Outer diameter of the blades mm 232
Gear ratio 1/35
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita KR400MP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita KR400MP in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info