Manual Makita JV143D (page 9 of 17) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691881

Zoom out

Zoom in

1/17

B) Plunge cutting (Fig. 14)

You need not bore a starting hole or make a lead-in

cut if you carefully do as follows.

(1) Tilt the tool up on the front edge of the base with

the blade point positioned just above the

workpiece surface.

(2) Apply pressure to the tool so that the front edge

of the base will not move when you switch on the

tool and gently lower the back end of the tool

slowly.

(3) As the blade pierces the workpiece, slowly lower

the base of the tool down onto the workpiece

surface.

(4) Complete the cut in the normal manner.

Finishing edges (Fig. 15)

To trim edges or make dimensional adjustments, run the

blade lightly along the cut edges.

Metal cutting

Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause significant blade wear.

The underside of the workpiece can be greased instead of

using a coolant.

Dust extraction (Fig. 16)

Clean cutting operations can be performed by connecting

this tool to a Makita vacuum cleaner. Insert the hose of

the vacuum cleaner into the hole at the rear of the tool.

Lower the dust cover before operation.

NOTE:

• Dust extraction cannot be performed when making

bevel cuts.

Rip fence (optional accessory)

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before installing or

removing accessories.

1. Straight cuts (Fig. 17)

When repeatedly cutting widths of 160 mm or less,

use of the rip fence will assure fast, clean, straight

cuts. (Fig. 18)

To install, insert the rip fence into the rectangular

hole on the side of the base with the fence guide

facing down. Slide the rip fence to the desired cutting

width position, then tighten the bolt to secure it.

2. Circular cuts

When cutting circles or arcs of 170 mm or less in

radius, install the rip fence as follows. (Fig. 19)

Insert the rip fence into the rectangular hole on the

side of the base with the fence guide facing up. Insert

the circular guide pin through either of the two holes

on the fence guide. Screw the threaded knob onto

the pin to secure the pin. (Fig. 20)

Now slide the rip fence to the desired cutting radius,

and tighten the bolt to secure it in place. Then move

the base all the way forward.

NOTE:

• Always use blades No. B-17, B-18, B-26 or B-27 when

cutting circles or arcs.

Anti-splintering device (optional

accessory) (Fig. 21)

For splinter-free cuts, the anti-splintering device can be

used. To install the anti-splintering device, move the tool

base all the way forward and fit it from the back of tool

base. When you use the cover plate, install the anti-

splintering device onto the cover plate.

CAUTION:

• The anti-splintering device cannot be used when

making bevel cuts.

Cover plate (Optional accessory) (Fig. 22)

Use the cover plate when cutting decorative veneers,

plastics, etc. It protects sensitive or delicate surfaces from

damage. Fit it on the back of the tool base.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Jig saw blades

•Hex wrench

• Rip fence (guide rule) set

• Anti-splintering device

• Hose (For vacuum cleaner)

• Cover plate (For aluminum base type)

• Makita genuine battery and charger

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 82 dB (A)

Sound power level (L

): 93 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita JV143D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 0,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita JV143D Manual

Product: