Manual Makita JV102D (page 10 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691877

Zoom out

Zoom in

1/80

10 ENGLISH

NOTE:Ifthetoolisleftfor10secondswithoutany

operation in the standby mode, the tool automatically

turns off and the lamp goes off.

NOTE: You can also stop and turn off the tool by

pressing the lock/unlock button while the tool is

operating.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

Toturnonthelamp,pressthelock/unlockbutton.To

turn off the lamp, press the lock/unlock button again.

NOTICE: When the tool is overheated, the lamp

ickers. Cool down the tool fully before operating

the tool again.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Speed adjusting dial

►Fig.5: 1.Speedadjustingdial

Thetoolspeedcanbeadjustedbyturningthespeed

adjustingdial.Youcangetthehighestspeedat5and

the lowest speed at 1.

Refer to the table to select the proper speed for the

workpiece to be cut. However, the appropriate speed

maydifferwiththetypeorthicknessoftheworkpiece.In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

Workpiece Number

Wood 4 - 5

Mild steel 3 - 5

Stainless steel 3 - 4

Aluminum 3 - 5

Plastics 1 - 4

NOTICE: When changing the speed dial from "5"

to "1", turn the dial counterclockwise. Do not turn

the dial clockwise forcibly.

Electronic function

Thetoolisequippedwiththeelectronicfunctionsfor

easy operation.

• Softstart

Thesoft-startfunctionminimizesstart-upshock,

and makes the tool start smoothly.

• Softno-loadrotation

Toreducethevibrationandalignthejigsawblade

with the cutting line easily, the tool automatically

reduces the rotation speed until the tool starts cut-

tingtheworkpiecewhenthespeedadjustingdial

is set at 2 or higher. Once the tool starts cutting

the workpiece, the tool speed reaches the preset

speed and keeps the speed until the tool stops.

NOTE: When the temperature is low, this function

may not be available.

Disabling the soft no-load rotation

function

Todisablethesoftno-loadrotationfunction,followthe

steps below.

1. Make sure that the tool is turned off.

2. Setthespeedadjustingdialto"1".

3. Press the lock/unlock button to turn on the tool.

4. Setthespeedadjustingdialto"5"byturningit,

andthensetitto"1"byturnitback.

Thelampblinkstwicetoindicatethatthesoftno-load

rotationfunctionisdisabled.Toenablethisfunction

again, perform the same procedure again.

NOTE:Ifthesoftno-loadrotationfunctionisdisabled,

the lamp blinks twice when the tool is turned on.

NOTE: You can also disable or enable the soft

no-load rotation function by changing the speed

adjustingdialfrom"5"to"1"andchangingitfrom"1"

to"5".

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing jig saw blade

CAUTION: Always clean out all chips or for-

eign matter adhering to the jig saw blade and/or

blade holder.Failuretodosomaycauseinsufcient

tightening of the blade, resulting in a serious personal

injury.

CAUTION: Do not touch the jig saw blade or

the workpiece immediately after operation.They

may be extremely hot and could burn your skin.

CAUTION: Always secure the jig saw blade

rmly.Insufcienttighteningoftheblademaycause

bladebreakageorseriouspersonalinjury.

CAUTION: Use only B type jig saw blades.

UsingbladesotherthanBtypecausesinsufcient

tightening of the blade, resulting in a serious personal

injury.

CAUTION: When you remove the jig saw

blade, be careful not to hurt your ngers with the

top of the blade or the tips of workpiece.

Beforeinstallingthejigsawblade,makesurethatthe

blade clamp lever is in the released position.

Toinstallthejigsawblade,inserttheblade(teethfacing

forward)intothebladeholder.Thelevermovestothe

xedpositionandthebladeislocked.Makesurethat

thebackedgeofthebladetsintotheroller.Pullthe

blade lightly to make sure that the blade does not fall off

during operation.

►Fig.6: 1. Jig saw blade holder 2. Released position

3. Fixed position

►Fig.7: 1. Jig saw blade holder 2. Jig saw blade

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita JV102D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 12,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita JV102D Manual

Product: