657989

Makita JV101D Manual

9
Zoom out
Zoom in
Previous page
1/68
Next page
9 ENGLISH
Cutouts
Cutoutscanbemadewitheitheroftwomethods
“Boringastartinghole”or“Plungecutting”.
Boring a starting hole
►Fig.14
For internal cutouts without a lead-in cut from an edge,
pre-drill a starting hole 12 mm or more in diameter.
Insertthejigsawbladeintothisholetostartyourcut.
Plunge cutting
►Fig.15
Youneednotboreastartingholeormakealead-incut
if you carefully do as follows.
1. Tiltthetooluponthefrontedgeofthebasewith
thejigsawbladepointpositionedjustabovethework-
piece surface.
2. Apply pressure to the tool so that the front edge of
thebasewillnotmovewhenyouswitchonthetooland
gentlylowerthebackendofthetoolslowly.
3. Asthejigsawbladepiercestheworkpiece,slowly
lowerthebaseofthetooldownontotheworkpiece
surface.
4. Complete the cut in the normal manner.
Finishing edges
►Fig.16
Totrimedgesormakedimensionaladjustments,runthe
jigsawbladelightlyalongthecutedges.
Metal cutting
Alwaysuseasuitablecoolant(cuttingoil)whencutting
metal.Failuretodosowillcausesignicantjigsaw
bladewear.Theundersideoftheworkpiececanbe
greased instead of using a coolant.
Dust extraction
►Fig.17: 1. Hose (optional accessory) 2. Dust cover
Cleancuttingoperationscanbeperformedbyconnect-
ing this tool to a Makita vacuum cleaner.
Insertthehoseofthevacuumcleanerintotheholeat
the rear of the tool.
Lowerthedustcoverbeforeoperation.
NOTE:Dustextractioncannotbeperformedwhen
makingbevelcuts.
Rip fence
Optional accessory
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before installing or removing accessories.
Straight cuts
When repeatedly cutting widths of 160 mm or less, use
of the rip fence will assure fast, clean, straight cuts.
►Fig.18: 1. Rip fence (Guide rule)
Toinstall,inserttheripfenceintotherectangularhole
onthesideofthebasewiththefenceguidefacing
down. Slide the rip fence to the desired cutting width
position,thentightenthebolttosecureit.
►Fig.19: 1. Hex wrench 2. Bolt 3. Fence guide 4. Rip
fence (Guide rule)
Circular cuts
When cutting circles or arcs of 170 mm or less in radius,
install the rip fence as follows.
►Fig.20: 1. Rip fence (Guide rule)
1. Inserttheripfenceintotherectangularholeonthe
sideofthebasewiththefenceguidefacingup.
2. Insertthecircularguidepinthrougheitherofthe
twoholesonthefenceguide.Screwthethreadedknob
onto the pin to secure the pin.
►Fig.21: 1.Threadedknob2. Fence guide 3. Rip
fence (Guide rule) 4.Pin
3.
Slide the rip fence to the desired cutting radius, and tighten
thebolttosecureitinplace.Thenmovethebaseallthewayforward.
NOTE:AlwaysusejigsawbladesNo.B-17,B-18,
B-26 or B-27 when cutting circles or arcs.
Anti-splintering device
Optional accessory, only for aluminum base model
CAUTION: The anti-splintering device cannot
be used when making bevel cuts.
►Fig.22: 1. Base 2. Anti-splintering device
Forsplinter-freecuts,theanti-splinteringdevicecanbe
used.Toinstalltheanti-splinteringdevice,movethetool
baseallthewayforwardandtitfromthebackoftoolbase.
When you use the cover plate, install the anti-splintering
device onto the cover plate.
Cover plate
Optional accessory, only for aluminum base model
►Fig.23: 1. Cover plate 2. Base
Use the cover plate when cutting decorative veneers,
plastics,etc.Itprotectssensitiveordelicatesurfaces
fromdamage.Fititonthebackofthetoolbase.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita JV101D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita JV101D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 12,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info