599031
4
Zoom out
Zoom in
Previous page
1/40
Next page
4
ENGLISH (Original instructions)
Explanation of general view
1 Slide switch
2 Gauge for stainless:
1.2 mm (3/64")
3 Gauge for mild steel:
1.6 mm (1/16")
4 Hex wrench
5 Loosen
6 Upper blade securing bolt
7 Lower blade
8 Upper blade
9 Blade holder
10 Thin washer
11 Tighten
12 No gap allowed
13 Yoke
14 Lower blade positioning screw
15 Cutting line
SPECIFICATIONS
Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
ENE037-1
Intended use
The tool is intended for cutting sheet steel and stainless
sheet steel.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
GEA010-1
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
GEB027-3
SHEAR SAFETY WARNINGS
1. Hold the tool firmly.
2. Secure the workpiece firmly.
3. Keep hands away from moving parts.
4. Edges and chips of the workpiece are sharp.
Wear gloves. It is also recommended that you
put on thickly bottomed shoes to prevent injury.
5. Do not put the tool on the chips of the work-
piece. Otherwise it can cause damage and trou-
ble on the tool.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
8. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
9. Avoid cutting electrical wires. It can cause seri-
ous accident by electric shock.
10. Do not operate the tool at no-load unnecessarily.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
Model JS1602
Max. cutting capacities
Steel up to 400 N/mm
2
1.6 mm (16 ga.)
Steel up to 600 N/mm
2
1.2 mm (18 ga.)
Steel up to 800 N/mm
2
0.8 mm (22 ga.)
Aluminum up to 200 N/mm
2
2.5 mm (13 ga.)
Min. cutting radius 30 mm
Strokes per minute (min
–1
) 4,000
Overall length 255 mm
Net weight 1.6 kg
Safety class /II
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita JS1602 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita JS1602 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info