448567
4
Zoom out
Zoom in
Previous page
1/7
Next page
ENGLISH
Explanation of general view
1 Screw
2 Screwdriver
3 Center blade
4 Hex wrench
5 Side blade
6 Bolt
7 Pin
8 Slide switch
9 Limit mark
0 Brush holder cap
SPECIFICATIONS
Model JS1660 JS1670
Max. cutting capacities
Steel up to 400 N/mm
2
............................................ 1.6 mm/16 ga 1.0 mm/20 ga
Steel up to 600 N/mm
2
............................................ 1.2 mm/18 ga 0.7 mm/23 ga
Steel up to 800 N/mm
2
............................................ 0.8 mm/22 ga 0.5 mm/26 ga
Aluminum up to 200 N/mm
2
.................................... 2.5 mm/13 ga 2.5 mm/13 ga
Min. cutting radius ...................................................... 30 mm
Strokes per minute ..................................................... 4,500 4,500
Overall length ............................................................. 304 mm 306 mm
Net weight ................................................................... 1.3 kg 1.3 kg
Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phaseAC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
Safety instructions.
ADDITIONAL SAFETY RULES ENB011-2
1. Hold the tool firmly.
2. Secure the workpiece firmly.
3. Keep hands away from moving parts.
4. Edges and chips of the workpiece are sharp.
Wear gloves. It is also recommended that you
put on thickly bottomed shoes to prevent
injury.
5. Do not put the tool on the chips of the work-
piece. Otherwise it can cause damage and
trouble on the tool.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
8. Do not touch the blade or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
9. Avoid cutting electrical wires. It can cause
serious accident by electric shock.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Adjusting the blade clearance (Fig.1&2)
For JS1660 Only
Important: Always be sure that the tool is switched off
and unplugged before adjusting the blade clearance.
Adjust the clearance between the side blade and the
center blade according to the thickness of the work-
piece.
First use a screwdriver to loosen the screw.
Then use the hex wrench to adjust the clearance by
tightening or loosening the bolt. There may be a slight
difference between clearances (A) and (B).
Check the smaller clearance with the thickness gauge
and adjust it.
When using the thickness gauge to adjust the blade
clearance, refer to the table below.
Workpiece thickness
(mm)
Marking on
thickness gauge
Less than 0.8 0.5
0.8 1.3 1.0
More than 1.3 1.5
After adjusting the clearance, tighten the screw
securely.
Lubrication (Fig. 3)
Before operation, lubricate the contact point of the
center blade and the pin. To keep good cutting
performance, also use a cutting lubricant from time to
time during operation.
4
JS1660/JS1670 (E) (’101. 1. 12)
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita JS 1660 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita JS 1660 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita JS 1660

Makita JS 1660 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info