382507
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
Switch action (Fig. 7, 8 & 9)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the “OFF”
position when released.
For tools with lock button
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
Tool speed can be adjusted by turning the speed change
knob. When the portion with
v mark is positioned
adjacent to the pointer, faster speed can be obtained by
turning the knob clockwise.
When the portion with
w mark is positioned adjacent
to the pointer, full speed can be obtained.
Continuous operation can be performed only when the
knob is set to the full speed position. To perform continu-
ous operation, pull the trigger fully and then push the lock
button up. To stop the tool from the locked position, pull
the trigger fully, then release it.
For tools with lock-off button
To prevent the trigger from being accidentally pulled, a
lock-off button is provided. To start the tool, push the
lock-off button up and pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
Tool speed can be adjusted by turning the speed change
knob. When the portion with
v mark is positioned
adjacent to the pointer, faster speed can be obtained by
turning the knob clockwise.
When the portion with
w mark is positioned adjacent
to the pointer, full speed can be obtained.
Operation (Fig. 10)
Press the shoe firmly against the workpiece. Do not allow
the tool to bounce. Bring the blade into light contact with
the workpiece. First, make a pilot groove, using a slower
speed. Then use a faster speed to continue cutting.
CAUTION:
Always use a suitable coolant (cutting oil) when cut-
ting metal. Failure to do so will cause premature
blade wear.
Always wear gloves to protect your hands from hot
flying chips when cutting metal.
Always press the shoe firmly against the workpiece
during operation. If the shoe is held away from the
workpiece during operation, strong vibration and/or
twisting will be produced, causing the blade to snap
dangerously.
Be sure to always wear suitable eye protection
which conforms with current national standards.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Replacement of carbon brushes (Fig. 11 & 12)
Replace carbon brushes when they are worn down to the
limit mark. Both identical carbon brushes should be
replaced at the same time.
To maintain product safety and reliability, repairs, mainte-
nance or adjustment should be carried out by a Makita
Authorized Service Centre.
Position Cutting action Applications
0
Straight line cutting action For cutting mild steel, stainless steel and plastics.
For clean cuts in wood and plywood.
I
Small orbit cutting action For cutting mild steel, aluminum and hard wood.
II
Medium orbit cutting action For cutting wood and plywood.
For fast cutting in aluminum and mild steel.
III
Large orbit cutting action For fast cutting in wood and plywood.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita jr3020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita jr3020 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita jr3020

Makita jr3020 User Manual - German, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info