599028

Makita JR105D Manual

7
Zoom out
Zoom in
Previous page
1/56
Next page
7ENGLISH
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Adjusting the shoe
►Fig.5: 1.Hexwrench 2.Hexbolt 3.Loosen
Whenthebladelosesitscuttingefciencyinoneplace
along its cutting edge, reposition the shoe to utilize a
sharp,unusedportionofitscuttingedge.Thiswillhelp
tolengthenthelifeoftheblade.
Torepositiontheshoe,loosentheboltwithhexwrench.
Slide the shoe to the desired position and then tighten
theboltrmly.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the recipro/jig
saw blade
CAUTION: Always clean out all chips or foreign
matter adhering to the blade, blade clamp and/or
slider.Failuretodosomaycauseinsufcienttighten-
ingoftheblade,resultinginaseriousinjury.
For Model JR103D
►Fig.6: 1.Reciprosawblade 2.Bladeclampsleeve
Insertthereciprosawbladeintothebladeclampasfar
asitwillgo.Thebladeclampsleeverotatesandxes
thereciprosawblade.Makesurethatthereciprosaw
bladecannotbeextractedeventhoughyoutrytopull
it out.
CAUTION: If you do not insert the recipro saw
blade deep enough, the recipro saw blade may be
ejected unexpectedly during operation.Thiscan
beextremelydangerous.
NOTE:Youcannotusethejigsawbladewith
JR103D.
►Fig.7: 1.Reciprosawblade 2.Bladeclampsleeve
Toremovethereciprosawblade,rotatetheblade
clampsleeveinthedirectionofthearrowfully.Thereci-
prosawbladeisremovedandthebladeclampsleeveis
xedatthereleasedposition.
NOTE:Ifyouremovethereciprosawbladewithout
rotatingthebladeclampsleevefully,thesleeve
maynotbexed.Inthiscase,rotatetheblade
clampsleevefully,thenmakethesleevexedatthe
released position.
For Model JR105D
►Fig.8: 1. Hex wrench 2. Bolt 3. Loosen
4.Tighten
►Fig.9: 1.Reciprosawblade 2.Hexwrench
3.Holeforreciprosawblade 4.Bladeclamp
Toinstalltherecipro/jigsawblade,loosentheboltby
hexwrench.Wheninstallingareciprosawblade,press
theboltwiththehexwrenchtoopentheslotduring
insertingtheblade.
►Fig.10: 1.Recipro/jigsawblade 2.Bladeclamp
3.Holeforreciprosawblade 4.Holeforjigsaw
blade
►Fig.11
Youcanusebothjigsawblades(Btype)andrecipro
sawbladesaccordingtoyourwork.Inserttherecipro/
jigsawbladestraightintothebladeclampandtighten
itbyhexwrench.Pulltherecipro/jigsawbladelightlyto
makesurethattherecipro/jigsawbladedoesnotfalloff
during operation.
Toremovetherecipro/jigsawblade,followtheinstalla-
tion procedure in reverse.
Hex wrench storage
►Fig.12: 1. Hex wrench 2. Protrusion
When not in use, store the hex wrench as shown in the
guretokeepitfrombeinglost.
OPERATION
CAUTION: Always press the shoe rmly
against the workpiece during operation. If the
shoe is held away from the workpiece during opera-
tion,strongvibrationand/ortwistingwillbeproduced,
causingthebladetosnapdangerously.
CAUTION: Always wear gloves to protect your
hands from hot ying chips when cutting metal.
CAUTION: Be sure to always wear suitable eye
protection which conforms with current national
standards.
CAUTION: Always use a suitable coolant (cut-
ting oil) when cutting metal. Failure to do so will
causeprematurebladewear.
►Fig.13
Presstheshoermlyagainsttheworkpiece.Donot
allowthetooltobounce.Bringthereciprosawblade
into light contact with the workpiece. First, make a pilot
grooveusingaslowerspeed.Thenuseafasterspeed
to continue cutting.
►Fig.14
►Fig.15
You can use the switch lever or trigger according to your
work.
NOTE: If the tool is operated continuously until the
batterycartridgehasdischarged,allowthetooltorest
for15minutesbeforeproceedingwithafreshbattery.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita JR105D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita JR105D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 9,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita JR105D

Makita JR105D User Manual - English, German, Polish - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info