Manual Makita JR 3070 (page 7 of 20) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

110257

Zoom out

Zoom in

1/20

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing saw blade

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade, blade clamp and/or slider. Failure to do so

may cause insufficient tightening of the blade, resulting

in a serious injury.

To install the saw blade, always make sure that the blade

clamp lever is in released position on the insulation

cover before inserting the saw blade. If the blade clamp

lever is in fixed position, rotate the blade clamp lever in

the direction of the arrow so that it can be locked at the

released position . (Fig. 6)

Insert the saw blade into the blade clamp as far as it will

go. The blade clamp sleeve rotates and the saw blade is

fixed. Make sure that the saw blade cannot be extracted

even though you try to pull it out. (Fig. 7)

NOTE:

• If you do not insert the saw blade deep enough, the

saw blade may be ejected unexpectedly during opera-

tion. This can be extremely dangerous.

To remove the saw blade, rotate the blade clamp lever in

the direction of the arrow fully. The saw blade is removed

and the blade clamp lever is fixed at the released position

. (Fig. 8)

NOTE:

• If you remove the saw blade without rotating the blade

clamp lever fully, the lever may not be locked in the

released position . In this case, rotate the blade

clamp lever fully again, then make sure that the blade

clamp lever locked at the released position .

OPERATION (FIG. 9)

CAUTION:

• Always press the shoe firmly against the workpiece

during operation. If the shoe is held away from the

workpiece during operation, strong vibration and/or

twisting will be produced, causing the blade to snap

dangerously.

• Always wear gloves to protect your hands from hot fly-

ing chips when cutting metal.

• Be sure to always wear suitable eye protection which

conforms with current national standards.

• Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause premature blade

wear.

Press the shoe firmly against the workpiece. Do not allow

the tool to bounce. Bring the blade into light contact with

the workpiece. First, make a pilot groove, using a slower

speed. Then use a faster speed to continue cutting.

MAITENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

Replacing carbon brushes (Fig. 10 & 11)

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Recipro saw blade

• Plastic carrying case

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita JR 3070 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita JR 3070 Manual

Product: