Manual Makita JR 180D (page 5 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

448557

Zoom out

Zoom in

1/52

ADDITIONAL SAFETY RULES FOR TOOL

1. Be aware that this tool is always in an operating

condition, because it does not have to be

plugged into an electrical outlet.

2. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear protec-

tors and thickly padded gloves.

3. Check the blade carefully for cracks or damage

before operation. Replace cracked or damaged

blade immediately.

4. Do not attempt to cut workpieces larger than

specified in this manual (especially hollow pipe).

The blade might snap and cause an injury.

(Fig. 1)

5. Hold the tool firmly.

6. Be sure no one is below when using the tool in

high locations.

7. Do not point the tool at anyone in the immediate

vicinity.

8. When making a “blind” cut (you can’t see behind

what is being cut), be sure that hidden electrical

wiring or water pipes are not in the path of the

cut. If wires are present, they must be discon-

nected at their power source by a qualified per-

son or avoided to prevent the possibility of lethal

shock or fire. Always hold the tool ONLY by the

insulated gripping surfaces to prevent any elec-

tric shock if you accidentally cut through a “live”

wire. Water pipes in “blind” areas must be

drained and capped before cutting.

9. Be careful not to hit the end of the blade against

something during operation. Damage to the tool

or dangerous blade breakage may occur. (Fig. 2)

10. Watch out for cut-off portions of the workpiece

being cut. They may fall and injure you or some-

one near you.

11. When cutting metals, be cautious of hot flying

chips.

12. Do not touch the blade or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

13. If you withdraw the blade from the workpiece

during operation, strong reaction will be pro-

duced, causing the blade to snap or causing you

to lose your grip and control of the tool. Always

switch off the tool and wait until the blade has

come to a complete stop before withdrawing the

blade from the workpiece.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 3)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the push buttons on both sides of

the cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

Charging (Fig. 4)

Your new battery cartridge is not charged. You will need to charge it before use. Use the battery charger to charge the

battery cartridge.

Plug the battery charger into the proper AC voltage source. The charging light will flash in green color. Insert the bat-

tery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective

markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When

the battery cartridge is inserted, the charging light color will change from green to red and charging wil begin. The

charging light will remain lit steadily during charging. When the charging light color changes from red to green, the

charging cycle is complete. Refer to the table below for the charging time. If you leave the battery cartridge in the

charger after the charging cycle is complete, the charger will switch into its “trickle charge (maintenance charge)”

mode which will last approximately 24 hours. After charging, unplug the charger from the power source.

CAUTION:

• The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufac-

turer’s batteries.

• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it

may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-

tery cartridge fully after discharging it completely and recharging a couple of times.

• If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location

exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a

while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the

battery cartridge from the battery charger.

Battery type Capacity (mAh) Number of cells Charging time

1422 2,000 12 Approx. 45 min.

1433 2,200 12 Approx. 50 min.

1434 2,600 12 Approx. 60 min.

1435 3,000 12 Approx. 70 min.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita JR 180D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita JR 180D

Makita JR 180D User Manual - English, Dutch - 13 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita JR 180D Manual

Product: