599024
6
Zoom out
Zoom in
Previous page
1/36
Next page
6
Punch & die service life
Replace or sharpen punch and die after cutting the
lengths indicated in the accompanying table. Their life,
of course, depends upon the thickness of materials cut
and lubrication conditions.
Punch Replace after 150 m of 3.2 mm steel sheet
Die Sharpen after 300 m of 3.2 mm steel sheet
006441
When cutting is poor even after replacing the punch,
sharpen the die. Grind down the dull edge shown in the
figure using a grinder. After rough-grinding the dull
portion, finish with a dressing stone. Stock removal
should be about 0.3 to 0.4 mm.
Fig.9
When installing ground die, a clearance of 3.5 to 4.0
mm should be obtained by attaching one or two of the
washer provided, as shown in the figure. Failure to have
the proper clearance will result in vibration during
cutting.
Fig.10
CAUTION:
Secure installing screws carefully when installing.
A loose screw can cause tool breakage during
operation.
NOTE:
The die can be sharpened two times. After two
sharpenings, it should be replaced with new one.
Replacing carbon brushes
Fig.11
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Fig.12
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
These accessories or attachments are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Die
Punch
Hex wrench
Wrench 50
Die height adjustment washer
NOTE:
Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita JN3201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita JN3201 in the language / languages: English, German, Polish as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info