691838
5
Zoom out
Zoom in
Previous page
1/18
Next page
5
ENGLISH (Original instructions)
Explanation of general view
1 Lever
2 Front lever
3 Rear wing nut
4 Stopper
5 0° position
6 45° position
7 Cutting line
8Screw
9 Switch trigger
10 Lock-off button
11 Light
12 Hex wrench
13 Loosen
14 Tighten
15 Shaft lock
16 Mounting shaft
17 Inner flange
18 Saw blade
19 Outer flange
20 Hex bolt
21 Ring
22 Dust nozzle
23 Vacuum cleaner
24 Hose
25 Clamp lever
26 Rip fence (Guide rule)
27 Adjusting screw for 0°
28 Adjusting screw for 45°
29 Triangular rule
30 Base
31 Limit mark
32 Screwdriver
33 Brush holder cap
SPECIFICATIONS
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
ENE078-1
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece. With
appropriate saw blades, aluminum can also be sawed.
ENF100-1
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.32 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
GEA010-1
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
GEB013-6
CIRCULAR SAW SAFETY WARNINGS
Cutting procedures
1. DANGER: Keep hands away from cutting
area and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both hands
are holding the saw, they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a
stable platform. It is important to support the work
properly to minimize body exposure, blade binding,
or loss of control.
000157
Model HS6100 HS6101 HS7100 HS7101
Blade diameter 165 mm 190 mm
Max. cutting depth
at 0° 54.5 mm 67 mm
at 45° 39.5 mm 48.5 mm
at 50° 35.5 mm 43.5 mm
No load speed (min
–1
) 5,500
Overall length 297 mm 310 mm
Net weight 3.7 kg 3.7 kg 4.0 kg 4.0 kg
Safety class /II
A typical illustration of proper hand support,
workpiece support, and supply cord routing (if
applicable).
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HS7100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HS7100 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info