Manual Makita HS301DZJ (page 8 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711053

Zoom out

Zoom in

1/72

8 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoffyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

►Fig.7: 1. Red indicator 2. Button 3. Battery

cartridge

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

notbeinginsertedcorrectly.

Battery protection system

Thetoolisequippedwithabatteryprotectionsystem.

Thissystemautomaticallycutsoffpowertothemotorto

extendbatterylife.

Thetoolwillautomaticallystopduringoperationifthe

tooland/orbatteryareplacedunderoneofthefollowing

conditions:

Overloaded:

Thetoolisoperatedinamannerthatcausesittodraw

anabnormallyhighcurrent.

In this situation, release the switch trigger on the tool

andstoptheapplicationthatcausedthetooltobecome

overloaded.Thenpulltheswitchtriggeragaintorestart.

Ifthetooldoesnotstart,thebatteryisoverheated.

Inthissituation,letthebatterycoolbeforepullingthe

switch trigger again.

Low battery voltage:

Theremainingbatterycapacityistoolowandthetool

will not operate. If you pull the switch trigger, the motor

runsagainbutstopssoon.Inthissituation,removeand

rechargethebattery.

Indicating the remaining battery

capacity

Only for battery cartridges with "B" at the end of the

model number

►Fig.8: 1.Indicatorlamps 2.Checkbutton

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for few seconds.

Indicator lamps Remaining

capacity

Lighted Off

75% to 100%

50% to 75%

25% to 50%

0% to 25%

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydifferslightly

from the actual capacity.

Adjusting depth of cut

►Fig.9: 1. Clamping screw 2. Depth guide

CAUTION: After adjusting the depth of cut,

always tighten the clamping screw securely.

Loosen the clamping screw on the depth guide and

movethebaseupordown.Atthedesireddepthofcut,

securethebasebytighteningtheclampingscrew.

For cleaner, safer cuts, set cut depth so that no more

thanonebladetoothprojectsbelowworkpiece.Using

proper cut depth helps to reduce potential for danger-

ousKICKBACKSwhichcancausepersonalinjury.

Bevel cutting

►Fig.10: 1. Clamping screw 2. Bevel scale plate

Loosentheclampingscrewonthebevelscaleplateon

thefrontofthebase.Setforthedesiredangle(0°-45°)

bytiltingaccordingly,thentightentheclampingscrew

securely.

Sighting

►Fig.11: 1. Cutting line

Forstraightcuts,aligntheApositiononthefrontofthe

basewithyourcuttingline.For45°bevelcuts,alignthe

B position with it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HS301DZJ in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 11,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HS301DZJ Manual

Product: