793651
22
Zoom out
Zoom in
Previous page
1/156
Next page
22 ENGLISH
MAINTENANCE
CAUTION:
Always be sure that the tool is switched
󰀨-
ing to perform inspection or maintenance.
CAUTION:
Clean out the upper and lower guards
to ensure there is no accumulated sawdust which may
impede the operation of the lower guarding system. A

󰀨
If
the dust is being blown out of the guards, be sure the
proper eye and breathing protection is used.
CAUTION: 󰀨
dust on the tool.

NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,



Adjusting 0°-cut or 45°-cut accuracy
NOTICE: Do not engage the levers for -1° bevel
angle when adjusting 0°-cut accuracy.
NOTICE:
Do not engage the positive stopper for 22.5°
or 60° bevel angle when adjusting 45°-cut accuracy.

󰀨
1. Loosen the clamping screws on the front and rear
of the tool so that the bevel angle can be changed. Set


Fig.46: 1. Clamping screw 2. Positive stopper
2.
Make the base perpendicular or 45° to the circular saw


Fig.47: 1. Triangular rule
Fig.48: 1.2.
screw for 45° angle
3. Tighten the clamping screws and then make a test
cut to check if desired angle is obtained.
Adjusting the depth guide


depth guide as follows:
1. Make the base perpendicular, and set the depth of
cut to the deepest.
 

 
 
for parallelism.
Fig.49: 1.
Adjusting the parallelism
CAUTION: Keep the parallelism accurate.




󰀨
1. Set the tool to the maximum cutting depth.
2. Make sure all levers and screws are tightened.
3. 
4. While opening the lower guard, move the rear of
the base so that the distance A and B becomes equal.
Fig.50: 1. Screw 2. Base
5. Tighten the screws and make a test cut to check
the parallelism.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool

accessories or attachments might present a risk of

for its stated purpose.
-

Center.
Circular saw blade
Sub base
Guide rail
Bevel guide
• Clamp
• Sheet
Rubber sheet
Position sheet
Hex wrench
 󰀨
Wireless unit
 
NOTE:

󰀨
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HS011G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HS011G in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 22.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info