Manual Makita HR262TD (page 8 of 19) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598565

Zoom out

Zoom in

1/19

Battery remaining capacity indicator (only

for models with Battery BL3622A)

Battery BL3622A is equipped with the battery remaining

capacity indicator. (Fig. 2)

Press the CHECK button to indicate the battery remaining

capacity. The indicator lamps will then light for approx.

three seconds.

011713

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery capacity has run out, so the tool does not

operate. In these cases, charge the battery or replace

the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, the battery has reached the

end of its service life.

• When the upper two and lower two indicator lamps light

alternately, the battery may have malfunctioned.

Contact your local Makita authorized service center.

NOTE:

• The indicated capacity may be lower than the actual

level during use or immediately after using the tool.

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

Switch action (Fig. 3)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Lighting up the lamp (Fig. 4)

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The light automatically goes out 10 - 15 seconds after the

switch trigger is released.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

• Do not use thinner or gasoline to clean the lamp. Such

solvents may damage it.

Reversing switch action (Fig. 5)

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

Changing the quick change chuck for

SDS-plus

For Model BHR262T, HR262TD

The quick change chuck for SDS-plus can be easily

exchanged for the quick change drill chuck.

Removing the quick change chuck for SDS-plus

(Fig. 6)

CAUTION:

• Before removing the quick change chuck for SDS-plus,

always remove the bit.

Grasp the change cover of the quick change chuck for

SDS-plus and turn in the direction of the arrow until the

change cover line moves from the symbol to the

symbol. Pull forcefully in the direction of the arrow.

Attaching the quick change drill chuck (Fig. 7)

Check the line of the quick change drill chuck shows the

symbol. Grasp the change cover of the quick change

drill chuck and set the line to the symbol.

Place the quick change drill chuck on the spindle of the

tool.

Grasp the change cover of the quick change drill chuck

and turn the change cover line to the symbol until a

click can clearly be heard.

Selecting the action mode

Rotation with hammering (Fig. 8)

For drilling in concrete, masonry, etc., depress the lock

button and rotate the action mode changing knob to the

symbol. Use a tungsten-carbide tipped bit.

Rotation only (Fig. 9)

For drilling in wood, metal or plastic materials, depress the

lock button and rotate the action mode changing knob to

the symbol. Use a twist drill bit or wood bit.

Hammering only (Fig. 10)

For chipping, scaling or demolition operations, depress

the lock button and rotate the action mode changing knob

to the symbol. Use a bull point, cold chisel, scaling

chisel, etc.

Indicator lamps

Remaining capacity

Lighted Off Blinking

E F

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may have

malfunctioned.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HR262TD in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HR262TD Manual

Product: