Manual Makita hr 4500 c (page 7 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388899

Zoom out

Zoom in

1/52

OPERATING INSTRUCTIONS

Installing or removing bit

CAUTION:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Clean the bit shank and apply the bit grease provided

to it before installing the bit. (Fig. 1)

Insert the bit into the tool. Turn the bit and push it in

until it engages. (Fig. 2)

If the bit cannot be pushed in, remove the bit. Pull the

chuck cover down a couple of times. Then insert the

bit again. Turn the bit and push it in until it engages.

(Fig. 3)

After installing, always make sure that the bit is

securely held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the

way and pull the bit out. (Fig. 4)

Selecting action mode

Rotation with hammering (Fig.5&6)

For drilling in concrete, masonry, etc., depress the

lock button and rotate the change lever so that the

pointer points to the

symbol. Use a tungsten-

carbide tipped bit.

Hammering only (Fig.5&7)

For chipping, scaling or demolition operations,

depress the lock button and rotate the change lever

so that the pointer points to the

symbol. Use a bull

point, cold chisel, scaling chisel, etc.

CAUTION:

•

Do not rotate the change lever when the tool is

running under load. The tool will be damaged.

•

To avoid rapid wear on the mode change mecha-

nism, be sure that the change lever is always

positively located in one of the two action mode

positions.

Bit angle

(when chipping, scaling or demolishing)

CAUTION:

Always be sure that the tool is switched off and

unplugged before changing the bit angle.

The bit can be secured at 16 different angles. To

change the bit angle, depress the lock button and

rotate the change lever so that the pointer points to

the V symbol. Turn the bit to the desired angle.

(Fig. 8)

Depress the lock button and rotate the change lever

so that the pointer points to the

symbol. (Fig. 9)

Then make sure that the bit is securely held in place

by turning it slightly.

Side handle (Fig. 10)

CAUTION:

Use the side handle only when chipping, scaling or

demolishing. Do not use it when drilling in concrete,

masonry, etc. The tool cannot be held properly with

this side handle when drilling.

The side handle can be swung 360° on the vertical

and secured at any desired position. It also secures at

eight different positions back and forth on the horizon-

tal. Just loosen the clamp nut to swing the side handle

to a desired position. Then tighten the clamp nut

securely.

Side grip (Fig. 11)

CAUTION:

Always use the side grip to ensure operating safety

when drilling in concrete, masonry, etc.

The side grip swings around to either side, allowing

easy handling of the tool in any position. Loosen the

side grip by turning it counterclockwise, swing it to the

desired position and then tighten it by turning clock-

wise.

Switch action (Fig. 12)

CAUTION:

Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

‘‘OFF’’ position when released.

To start the tool, simply pull the trigger. Release the

trigger to stop.

Speed change (Fig. 13)

The revolutions and blows per minute can be adjusted

just by turning the adjusting dial. The dial is marked 1

(lowest speed) to 6 (full speed). Refer to the table

below for the relationship between the number set-

tings on the adjusting dial and the revolutions/blows

per minute.

Number on

adjusting dial

Revolutions

per minute

Blows per

minute

6 240 2,550

5 230 2,450

4 200 2,100

3 160 1,700

2 130 1,300

1 120 1,250

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita hr 4500 c in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita hr 4500 c

Makita hr 4500 c User Manual - English, Dutch - 17 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita hr 4500 c Manual

Product: