Manual Makita hr 4011 c (page 7 of 56) (German, Danish, French, Italian, Portuguese, Spanish)

388901

Zoom out

Zoom in

1/56

14. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action

FOR MODEL HR4011C

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop. (Fig. 1)

FOR MODELS HR4010C AND HR4001C

Trigger switch

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

• This switch functions when setting the tool in sym-

bol and symbol modes.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop. (Fig. 1)

Slide switch

CAUTION:

• Before plugging in the tool, always check to see that

the tool is switched off.

• This switch functions only when setting the tool in

symbol action mode.

When using the tool in the hammering mode for a long

time, the slide switch is available. To start the tool, push

the “I (ON)” side of the switch lever. To stop the tool, push

the “O (OFF)” side of the switch lever. (Fig. 2)

Speed change (Fig. 3)

The revolutions and blows per minute can be adjusted

just by turning the adjusting dial. The dial is marked 1

(lowest speed) to 5 (full speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the revolutions/

blows per minute.

CAUTION:

• If the tool is operated continuously at low speeds for a

long time, the motor will get overloaded, resulting in

tool malfunction.

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

Selecting the action mode

Rotation with hammering (Fig. 4 & 5)

For drilling in concrete, masonry, etc., depress the lock

button and rotate the change lever so that the pointer

points to the symbol. Use a tungsten-carbide tipped

bit.

Hammering only

FOR MODELS HR4001C AND HR4010C (Fig. 6)

For chipping, scaling or demolition operations, depress

the lock button and rotate the change lever so that the

pointer points to the symbol. Use a bull point, cold

chisel, scaling chisel, etc.

For long time hammering (FOR MODELS HR4001C

AND HR4010C ONLY) (Fig. 7)

For chipping, scaling or demolition operations, depress

the lock button and rotate the change lever so that the

pointer points to the symbol. Use a bull point, cold

chisel, scaling chisel, etc.

CAUTION:

• When using the tool in the symbol mode, the switch

trigger does not work and only the slide switch works.

FOR MODEL HR4011C (Fig. 8)

For chipping, scaling or demolition operations, depress

the lock button and rotate the change lever so that the

pointer points to the symbol. Use a bull point, cold

chisel, scaling chisel, etc.

CAUTION:

• Do not rotate the change lever when the tool is running

under load. The tool will be damaged.

• To avoid rapid wear on the mode change mechanism,

be sure that the change lever is always positively

located in one of the two or three action mode posi-

tions.

Number on

adjusting dial

Revolutions

per minute

Blows

per minute

5 480 2,750

4 440 2,550

3 360 2,050

2 270 1,550

1 230 1,350

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita hr 4011 c in the language / languages: German, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita hr 4011 c

Makita hr 4011 c User Manual - English, Dutch - 23 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita hr 4011 c Manual

Product: