448540

Makita HR 3550C Manual

7
Zoom out
Zoom in
Previous page
1/23
Next page
ENGLISH
Explanation of general view
1 Bit grease
2 Bit shank
3 Bit
4 Chuck cover
5 Change lever
6 Shift lever
7 ‘‘Rotation with hammering’’
symbol
8 Lock button
9 Pointer
10 ‘‘Hammering only’’ symbol
11 ‘‘Rotation only’’ symbol
12 Loosen
13 Tighten
14 Side grip
15 Switch trigger
16 Adjusting dial
17 Clamp screw
18 Depth gauge
19 Power-ON indicator lamp
(green)
20 Service indicator lamp (red)
21 Screwdriver
22 Brush holder cover
23 Brush holder cap
24 Screws
25 Connector
26 Black
27 White
28 Crank cap
29 Hex wrench
30 Hammer grease
31 Drill chuck
SPECIFICATIONS
Model HR3550C
Capacities
Tungsten-carbide tipped bit ........................ 35 mm
Core bit ....................................................... 90 mm
Wood .......................................................... 30 mm
Steel ........................................................... 13 mm
No load speed (min
-1
) ............................... 360 – 720
Blows per minute ................................ 1,650 – 3,300
Overall length ............................................... 420 mm
Net weight ....................................................... 4.9 kg
•
Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
•
Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed the
safety instructions.
ADDITIONAL SAFETY RULES FOR
TOOL
ENB010-1
1. Hold tools by insulated gripping surfaces
when performing an operation where the cut-
ting tool may contact hidden wiring or its own
cord. Contact with a ‘‘live’’ wire will make
exposed metal parts of the tool ‘‘live’’ and
shock the operator.
2. Wear ear protectors when using the tool for
extended periods. Prolonged exposure to high
intensity noise can cause hearing loss.
3. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
4. Be sure the bit is secured in place before
operation.
5. Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
6. In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
7. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
8. Hold the tool firmly with both hands.
9. Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Do not point the tool at any one in the area
when operating. The bit could fly out and
injure someone seriously.
12. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
HR3550C (E) (’100. 8. 21)
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HR 3550C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HR 3550C in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info