Manual Makita HR 3541FC (page 6 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448539

Zoom out

Zoom in

1/52

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

Lighting up the lamp

For Model HR3541FC (Fig. 2)

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to turn on the light. The lamp keeps

on lighting while the switch trigger is being pulled.

The lamp turns off 10 - 20 seconds after releasing the

trigger.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp.

Be careful not to scratch the lens of lamp, or it may

lower the illumination.

Speed change (Fig. 3)

The revolutions and blows per minute can be adjusted just

by turning the adjusting dial. The dial is marked 1 (lowest

speed) to 5 (full speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the revolutions/

blows per minute.

CAUTION:

• If the tool is operated continuously at low speeds for a

long time, the motor will get overloaded, resulting in

tool malfunction.

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

Selecting the action mode

Rotation with hammering (Fig. 4)

For drilling in concrete, masonry, etc., depress the lock

button and rotate the change lever so that the pointer

points to the symbol. Use a tungsten-carbide tipped

bit.

Rotation only (Fig. 5)

For drilling in wood or metal, materials, etc., depress the

lock button and rotate the change lever so that the pointer

points to the symbol. Use a twist drill bit or wood bit.

Hammering only (Fig. 6)

For chipping, scaling or demolition operations, depress

the lock button and rotate the change lever so that the

pointer points to the symbol. Use a bull point, cold

chisel, scaling chisel, etc.

CAUTION:

• Do not rotate the change lever when the tool is running

under load. The tool will be damaged.

• To avoid rapid wear on the mode change mechanism,

be sure that the change lever is always positively

located in one of the three action mode positions.

Torque limiter

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

CAUTION:

• As soon as the torque limiter actuates, switch off the

tool immediately. This will help prevent premature wear

of the tool.

Indicator lamp (Fig. 7)

The green power-ON indicator lamp lights up when the

tool is plugged. If the indicator lamp does not light up, the

main cord or the controller may be defective. The indicator

lamp is lit but the tool does not start even if the tool is

switched on, the carbon brushes may be worn out, or the

controller, the motor or the ON/OFF switch may be

defective.

The red service indicator lamp lights up when the carbon

brushes are nearly worn out to indicate that the tool needs

servicing. After approx. 8 hours of use, the motor will

automatically be shut off.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Number on

adjusting dial

Revolutions per

minute

Blows per minute

5 630 3,300

4 590 3,100

3 480 2,500

2 370 1,900

1 315 1,650

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HR 3541FC in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HR 3541FC Manual

Product: