448524
5
Zoom out
Zoom in
Previous page
1/10
Next page
5
ENGLISH
Explanation of general view
1Tighten
2Loosen
3 Side grip
4 Bit shank
5 Bit grease
6Bit
7 Chuck cover
8 Clamp screw
9 Depth gauge
10 Switch trigger
11 Reversing switch lever
12 Action mode changing knob
13 Blow-out bulb
14 Dust cup
15 Chuck adapter
16 Keyless drill chuck
17 Sleeve
18 Ring
19 Tighten
20 Loosen
21 Wrench
22 Soft jaws
23 Screw
SPECIFICATIONS
Model HR2410/HR2410X HR2413
Capacities
Concrete ................................................................................... 24 mm 24 mm
Wood ........................................................................................ 32 mm 32 mm
Steel ......................................................................................... 13mm 13mm
No load speed (min
-1
) .................................................................. 0 1,050 0 1,050
Blows per minute ......................................................................... 0 4,900 0 4,900
Overall length .............................................................................. 371 mm 371 mm
Net weight .................................................................................... 2.4 kg 2.3 kg
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Note: Specifications may differ from country to country.
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone. It is also suitable for drilling
without impact in wood, metal, ceramic and plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear protec-
tors and thickly padded gloves.
2. Be sure the bit is secured in place before opera-
tion.
3. Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
4. In cold weather or when the tool has not been
used for a long time, let the tool warm up for sev-
eral minutes by operating it under no load. This
will loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
5. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
6. Hold the tool firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the tool running. Operate the tool
only when hand-held.
9. Do not point the tool at any one in the area when
operating. The bit could fly out and injure some-
one seriously.
10. When drilling or chipping into walls, floors or
wherever “live” electrical wires may be encoun-
tered, DO NOT TOUCH ANY METAL PARTS OF
THE TOOL!
Hold the tool by the insulated grasping surfaces
to prevent electric shock if you drill or chip into a
“live” wire.
11. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Side grip (auxiliary handle) (Fig. 1)
The side grip swings around to either side, allowing easy
handling of the tool in any position. Loosen the side grip
by turning it counterclockwise, swing it to the desired
position and then tighten it by turning clockwise.
Installing or removing drill bit
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Clean the bit shank and apply bit grease before installing
the bit. (Fig. 2)
Insert the bit into the tool. Turn the bit and push it in until
it engages. (Fig. 3)
If the bit cannot be pushed in, remove the bit. Pull the
chuck cover down a couple of times. Then insert the bit
again. Turn the bit and push it in until it engages. (Fig. 4)
After installing, always make sure that the bit is securely
held in place by trying to pull it out.
To remove the bit, pull the chuck cover down all the way
and pull the bit out.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HR 2410X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HR 2410X in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita HR 2410X

Makita HR 2410X User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info