Manual Makita hp 2032 (page 6 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388607

Zoom out

Zoom in

1/52

For HP2033 (Fig. 3)

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far

as it will go. Hold the ring firmly and turn the sleeve

clockwise until the chuck is tightened with a little click.

After the click, always tighten the chuck additionally to

prevent accidental loosening during operation.

To remove the bit, hold the ring and turn the sleeve

counterclockwise.

Depth gauge (Fig. 4)

The depth gauge is convenient for drilling holes of

uniform depth. Loosen the side grip and insert the

depth gauge into the hole in the side grip. Adjust the

depth gauge to the desired depth and tighten the side

grip.

NOTE:

The depth gauge cannot be used at the position

where the depth gauge strikes against the gear

housing.

Switch action (Fig. 5)

CAUTION:

Before plugging in the machine, always check to see

that the switch trigger actuates properly and returns to

the ‘‘OFF’’ position when released.

For HP2032 and HP2033

To start the machine, simply pull the trigger. Machine

speed is increased by increasing pressure on the

trigger. Release the trigger to stop. For continuous

operation, pull the trigger and then push in the lock

button. To stop the machine from the locked position,

pull the trigger fully, then release it.

For HP2034

To start the machine, simply pull the trigger. Release

the trigger to stop. For continuous operation, pull the

trigger and then push in the lock button. To stop the

machine from the locked position, pull the trigger fully,

then release it.

Reversing switch action (Fig. 6)

For HP2032 and HP2033

CAUTION:

•

Always check the direction of rotation before opera-

tion.

•

Use the reversing switch only after the machine

comes to a complete stop. Changing the direction of

rotation before the machine stops may damage the

machine.

This machine has a reversing switch to change the

direction of rotation. Move the reversing switch lever

to the

position for clockwise rotation or

the

position for counterclockwise rotation.

Speed change knob (Fig. 7)

Two rpm ranges can be preselected with the speed

change knob. Turn the speed change knob to the

position 1 or position 2.

Position 1:0 – 850 rpm (Fig. 7-1)

Position 2:0 – 2,900 rpm. (Fig. 7-2)

If it is hard to turn the knob, first turn the chuck slightly

in either direction and then turn the knob again.

Selecting action mode (Fig. 8)

This machine has an action mode change knob.

For rotation with hammering, turn the action mode

change knob to the posision of

symbol. (Fig. 8-1)

For rotation only, turn the action mode change knob to

the position of

symbol. (Fig. 8-2)

CAUTION:

Always turn the action mode change knob all the way

to your desired mode position. If you operate the

machine with the kob positioned half-way between

the mode symbols, the machine may be damaged.

Operation

1) Hammer drilling operation

When drilling in concrete, granite, tile, etc., turn

the action mode change knob to the position of

symbol to use ‘‘rotation with hammering’’

action. Be sure to use a tungsten-cabide tipped

bit. Do not apply more pressure when the hole

becomes clogged with chips or particles. Instead,

run the machine at an idle, then remove the bit

partially from the hole. By repeating this several

times, the hole will be cleaned out.

After drilling the hole, use the blow-out bulb to

clean the dust out of the hole. (Fig. 9)

2) Drillng operation

When drilling in wood, metal or plastic materials,

turn the action mode change knob to the position

symbol to use ‘‘rotation only’’ action.

•

Drilling in wood

When drilling in wood, best results are obtained

with wood drills equipped with a guide screw.

The guide screw makes drilling easier by pulling

the bit into the workpiece.

•

Drilling in metal

To prevent the bit from slipping when starting a

hole, make an indentation with a centerpunch

and hammer at the point to be drilled. Place the

point of the bit in the indentation and start

drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be

drilled dry.

CAUTION:

•

Pressing excessively on the machine will not

speed up the drilling. In fact, this excessive

pressure will only serve to damage the tip of

your bit, decrease the machine performance

and shorten the service life of the machine.

•

There is a tremendous twisting force exerted on

the machine/bit at the time of hole breakthrough.

Hold the machine firmly and exert care when the

bit begins to break through the workpiece.

•

A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to

back out. However, the machine may back out

abruptly if you do not hold it firmly.

•

Always secure small workpieces in a vise or

similar hold-down device.

HP2032/HP2033 (E) (’101. 2. 13)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita hp 2032 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita hp 2032

Makita hp 2032 User Manual - English, Dutch - 10 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita hp 2032 Manual

Product: