Manual Makita HM1802 (page 5 of 36) (English, German, Polish)

599621

Zoom out

Zoom in

1/36

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function

on the tool.

Switch action

CAUTION:

• Before plugging in the tool, always check to see

that the switch lever actuates properly and returns

to the "OFF" position when released.

Fig.1

To start the tool, simply squeeze the switch lever.

Release the switch lever to stop.

For model HM1812 only

NOTE:

• Blows at no load per minute becomes smaller than

those on load in order to reduce vibration under no

load, but this does not show trouble. Once

operation starts with a bit against concrete, blows

per minute increase. When temperature is low and

there is less fluidity in grease, the tool may not

have this function even with the motor rotating.

Indicator lamps

Fig.2

The green power-ON indicator lamp lights up when the

tool is plugged. The indicator lamp is lit but the tool does

not start even if the tool is switched on, the carbon

brushes may be worn out, or the controller, the motor or

the ON/OFF switch may be malfunction. The red service

indicator lamp flickers up when the carbon brushes are

nearly worn out to indicate that the tool needs servicing.

After some period of use, motor will automatically be

shut off.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

Installing soft grip

Fig.3

Soft grip is NOT installed before factory shipment.

Install soft grip securely.

Fig.4

Set the triangle alignment marks on the hammer body

and on the soft grip when installing the soft grip.

Installing or removing the bit

(optional accessory)

CAUTION:

• Always assure that the bit is securely retained by

attempting to pull the bit out of the tool holder after

installing the bit.

• Follow the below 2 installation methods in

accordance with the 2 different types of bits. If

inappropriate installation method is selected, the

bit cannot be secured.

Fig.5

This tool accepts bits either with or without a collar on

its shank.

To install the bit, follow either procedure (1) or (2)

described below.

(1) For bits with a collar

Fig.6

Pivot the tool retainer downward (approx. 60 degrees).

Insert the bit into the tool holder until it stops. Return the

tool retainer and secure the bit.

(2) For bits without a collar

Fig.7

Pivot the tool retainer upward (approx. 60 degrees).

Face the notched portion of the bit upward. Insert the bit

into the tool holder until it stops. Pivot the tool retainer

further until it stops at the tool holder.

To remove the bit, follow the installation procedure in

reverse.

OPERATION

Chipping/Scaling/Demolition

CAUTION:

• Keep well-balanced posture when holding the

heavy tool before / during / after operation to avoid

personal injuries.

• Secure debris in case of breaking it into smaller

pieces.

• Hold the tool firmly with both hands. Turn the tool

on and apply slight pressure on the tool so that the

tool will not bounce around, uncontrolled. Pressing

very hard on the tool will not increase the

efficiency.

• Do not pull out the tool if stuck. Instead, break the

work around the bit tip.

• Be sure to place the tool on the stable floor or

ground after use.

Fig.8

Always use the soft grip (auxiliary handle) and firmly

hold the tool by both side grip and switch handle during

operations.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HM1802 in the language / languages: English, German, Polish as an attachment in your email.

The manual is 1,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HM1802 Manual

Product: