Manual Makita HM1130C (page 6 of 36) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

599548

Zoom out

Zoom in

1/36

OPERATING INSTRUCTIONS

Installing or removing bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Clean the bit shank and apply the bit grease provided to

it before installing the bit. (Fig. 1)

Insert the bit into the tool holder cap. (Fig. 2)

If the bit cannot be pushed in, remove the bit. Pull the tool

holder cover down a couple of times. Then insert the bit

again. After installing, always make sure that the bit is

securely held in place by trying to pull it out. (Fig. 3)

To remove the bit, pull the tool holder cover down all the

way and pull the bit out. (Fig. 4)

Side handle (auxiliary handle) (Fig. 5)

The side handle can be swung 360° on the vertical and

secured at any desired position. It also secures at eight

different positions back and forth on the horizontal. Just

loosen the clamp nut to swing the side handle to a

desired position. Then tighten the clamp nut securely.

Switch action (Fig. 6)

CAUTION:

Before plugging in the tool, always check to see that the

tool is switched off.

To start the tool, push the “ON I” button on the left side of

the tool. To stop the tool, push the “OFF O” button on the

right side of the tool.

Speed change (Fig. 7)

For HM1130C only

The blows per minute can be adjusted between 1,300

and 2,650 BPM just by turning the adjusting dial. This

can be done even while the tool is running. The dial is

marked 1 (lowest speed) to 5 (full speed). Refer to the

table below for the relationship between the number set-

tings on the adjusting dial and the blows per minute.

Chipping / Scaling / Demolition (Fig. 8)

Hold the tool firmly with both hands. Turn the tool on and

apply slight pressure on the tool so that the tool will not

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 9 & 10)

Whenever carbon brushes must be replaced, they cut out

the tool automatically. When this occurs, loosen the

screws which secure the rear cover. Pry up the rear cover

with a screwdriver and remove it. Then replace both car-

bon brushes at the same time. Use only identical carbon

brushes.

Lubrication (Fig. 11 & 12)

This tool requires no hourly or daily lubrication because it

has a grease-packed lubrication system. Lubricate the

tool every time the carbon brushes are replaced.

Run the tool for several minutes to warm it up. Switch off

and unplug the tool. Remove the crank cap using a

socket wrench. Rest the tool on the table with the bit end

pointing upwards. This will allow the old grease to collect

inside the crank housing. Wipe out the old grease inside

and replace with a fresh grease (30 g). Use only Makita

genuine grease (optional accessory). Filling with more

than the specified amount of grease (approx. 30 g) can

cause faulty hammering action or tool failure. Fill only

with the specified amount of grease. Reinstall the crank

cap and tighten with the socket wrench. Do not tighten

the crank cap excessively. It is made of resin and is sub-

ject to breakage.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Centre.

Number on

adjusting dial

Blows per minute

52,650

42,350

31,950

21,550

11,300

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HM1130C in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HM1130C Manual

Product: