Manual Makita HM 1307CB (page 5 of 40) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448495

Zoom out

Zoom in

1/40

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the tool is switched off.

• Switch can be locked in “ON” position for ease of

operator comfort during extended use. Apply caution

when locking tool in “ON” position and maintain firm

grasp on tool.

To start the tool, push the switch lever “ON (I)” on the left

side of the tool. To stop the tool, push the switch lever

“OFF (O)” on the right side of the tool.

Speed change (Fig. 2)

The blows per minute can be adjusted just by turning the

adjusting dial. This can be done even while the tool is

running. The dial is marked 1 (lowest speed) to 5 (full

speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the blows per

minute.

For model HM1317C, HM1317CB only

NOTE:

• Blows at no load per minute becomes smaller than

those on load in order to reduce vibration under no

load, but this does not show trouble. Once operation

starts with a bit against concrete, blows per minute

increase and get to the numbers as shown in the table.

When temperature is low and there is less fluidity in

grease, the tool may not have this function even with

the motor rotating.

CAUTION:

• The adjusting dial can be turned only as far as 5 and

back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

Indicator lamp (Fig. 3)

The green power-ON indicator lamp lights up when the

tool is plugged. If the indicator lamp does not light up, the

mains cord or the controller may be malfunction. The

indicator lamp is lit but the tool does not start even if the

tool is switched on, the carbon brushes may be worn out,

or the controller, the motor or the ON/OFF switch may be

malfunction.

The red service indicator lamp flickers up when the

carbon brushes are nearly worn out to indicate that the

tool needs servicing. After approx. 8 hours of use, the

motor will automatically be shut off.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Side handle (auxiliary handle) (Fig. 4)

The side handle can be swung 360° on the vertical and

secured at any desired position. Just loosen the clamp nut

to swing the side handle to a desired position. Then

tighten the clamp nut securely.

Installing or removing the bit

For Model HM1307C, HM1317C only (Fig. 5)

With the notched portion on the shank of the bit facing

toward the tool retainer, insert the bit into the tool holder

as far as it will go. Then pull out and turn the tool retainer

180° to secure the bit. After installing, always make sure

that the bit is securely held in place by trying to pull it out.

For Model HM1307CB, HM1317CB only (Fig. 6)

This tool accepts bits either with or without a collar on its

shank.

(1) For bits with a collar (Fig. 7)

To install the bit, follow either procedure (1) or (2)

described below.

Pivot the tool retainer back and slightly downward.

Insert the bit into the tool holder as far as it will go. To

securely retain the bit, return the tool retainer to its

original position.

CAUTION:

• Always assure that the bit is securely retained by

attempting to pull the bit out of the tool holder after

completing the above procedure.

(2) For bits without a collar (Fig. 8)

Pivot the tool retainer forward and slightly downward.

With the notched portion of the bit facing the tool

retainer shaft, insert the bit into the tool holder as far

as it will go. Then pivot the tool retainer further

downward toward the barrel to securely retain the bit.

CAUTION:

• Always assure that the bit is securely retained by

attempting to pull the bit out of the tool holder after

completing the above procedure.

• The bit without a collar cannot be retained by the

method shown in Fig. 7.

To remove the bit, follow the installation procedure in

reverse.

OPERATION

Chipping/Scaling/Demolition (Fig. 9)

Always use the side grip (auxiliary handle) and firmly hold

the tool by both side grip and switch handle during

operations. Turn the tool on and apply slight pressure on

the tool so that the tool will not bounce around,

uncontrolled. Pressing very hard on the tool will not

increase the efficiency.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

Number on adjusting dial Blows per minute

5 1,450

4 1,350

3 1,150

2800

1730

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HM 1307CB in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HM 1307CB Manual

Product: