Manual Makita HM 1303 (page 4 of 32) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

448491

Zoom out

Zoom in

1/32

ENGLISH

Explanation of general view

1 Bull point

2 Tool retainer

3 Notched portion

4Dust cover

5 Tool holder

6 Projecting portion of

side handle

7 Notch on set bolt

8 Set bolt

9Nut

10 Side handle

11 Lock button

12 Switch trigger

13 Screwdriver

14 Holder cap plate

15 Brush holder cap

16 Plate 50

17 Hammer grease

SPECIFICATIONS

Model HM1303

Blows per minute..................................................... 1,450

Overall length ...................................................... 747 mm

Net weight .............................................................. 14 kg

• Due to our continuing programme of research and

development, the specifications herein are subject to

change without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

be operated on single-phase AC/DC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear protec-

tors and thickly padded gloves.

2. Be sure the bit is secured in place before opera-

tion.

3. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

4. In cold weather or when the tool has not been

used for a long time, let the tool warm up for sev-

eral minutes by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is difficult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

6. Hold the tool firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not point the tool at anyone in the area when

operating. The bit could fly out and injure some-

one seriously.

10. When chipping into walls, floors or wherever

“live” electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE TOOL!

Hold the tool by the insulated grasping surfaces

to prevent electric shock if you chip into a “live”

wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing the bit (Fig. 1)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

With the notched portion on the shank of the bit facing

toward the tool retainer, insert the bit into the tool holder

as far as it will go. Then pull out and turn the tool retainer

180° to secure the bit. After installing, always make sure

that the bit is securely held in place by trying to pull it out.

When installing the scaling chisel, clay spade or rammer,

remove the dust cover from the tool.

Side handle (auxiliary handle) (Fig. 2)

The side handle can be either freely swivelled or secured

at one position for use during tool operation. Just loosen

the nut to swivel the handle freely.

To secure the handle at a fixed position, first loosen the

nut and swing the handle to the desired position for use.

Then tighten the nut firmly. If the set bolt turns together

with the nut when you secure the nut, see that the pro-

jecting portion of the side handle fits into the notch on the

head of the set bolt.

Switch action (Fig. 3)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then slide down the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

Chipping / Scaling / Demolition

Hold the tool firmly with both hands. Turn the tool on and

apply slight pressure on the tool so that the tool will not

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HM 1303 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita HM 1303

Makita HM 1303 User Manual - English, Dutch - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HM 1303 Manual

Product: