Manual Makita hm 1202 c (page 6 of 44) (German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388900

Zoom out

Zoom in

1/44

ENGLISH

Explanation of general view

1 Bit grease

2 Bit shank

3 Tool holder cover

4Bit

5 Change ring

6 Side handle (auxiliary handle)

7 Can be swung 360° on the

vertical and secured at any

desired position

8 Secures at eight different

positions back and forth

on the horizontal

9 Clamp nut

10 Loosen

11 Tighten

12 Side handle base

13 Switch lever

14 ON

15 OFF

16 Adjusting dial

17 Power-ON indicator lamp

(green)

18 Service indicator lamp (red)

19 Screwdriver

20 Rear cover

21 Screws

22 Brush holder cap

23 Screws

24 Handle

25 Socket wrench

26 Crank cap

27 Hammer grease

SPECIFICATIONS

Model HM1202 HM1202C

Blows per minute ......................................................................... 1,900 950 – 1,900

Overall length .............................................................................. 578 mm 578 mm

Net weight ................................................................................... 9.3 kg 9.3 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

For public low-voltage distribution systems of

between 220 V and 250 V

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.46 Ohms it can be presumed that

there will be no negative effects.

The mains socket used for this device must be protected

with a fuse or protective circuit breaker having slow trip-

ping characteristics.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

ENB009-1

1. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring or its own cord. Con-

tact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Wear ear protectors when using the tool for

extended periods. Prolonged exposure to high

intensity noise can cause hearing loss.

3. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask and thickly

padded gloves.

4. Be sure the bit is secured in place before opera-

tion.

5. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

6. In cold weather or when the tool has not been

used for a long time, let the tool warm up for a

while by operating it under no load. This will

loosen up the lubrication. Without proper warm-

up, hammering operation is difficult.

7. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

8. Hold the tool firmly with both hands.

9. Keep hands away from moving parts.

10. Do not leave the tool running. Operate the tool

only when hand-held.

11. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

12. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Clean the bit shank and apply the bit grease provided

to it before installing the bit. (Fig. 1)

Pull the tool holder cover down all the way. (Fig. 2)

Insert the bit into the tool. Turn the bit and push it in

until it engages. (Fig. 3-1)

Release the tool holder cover. It will return automati-

cally to its original position to secure the bit.

(Fig. 3-2)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita hm 1202 c in the language / languages: German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita hm 1202 c

Makita hm 1202 c User Manual - English, Dutch - 11 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita hm 1202 c Manual

Product: