388900
7
Zoom out
Zoom in
Previous page
1/11
Next page
7
After installing, always make sure that the bit is
securely held in place by trying to pull it out.
To remove the bit, pull the tool holder cover down all
the way and pull the bit out. (Fig. 4)
Bit angle (Fig. 5)
The bit can be secured at 12 different angles. To
change the bit angle, slide the change ring forward,
then turn the change ring to change the bit angle. At
the desired angle, slide the change ring back to the
original position. The bit will be secured in place.
NOTE:
The change ring cannot turn when the bit is not
installed on the tool.
Side handle (auxiliary handle)
The side handle can be swung 360° on the vertical
and secured at any desired position. It also secures
at eight different positions back and forth on the hori-
zontal. Just loosen the clamp nut to swing the side
handle to a desired position. Then tighten the clamp
nut securely. (Fig. 6)
The side handle also can be mounted in the rear
groove as shown in Fig. 7. Loosen the clamp nut and
widen the side handle base. Slide the side handle
back to the rear groove and secure it with the clamp
nut. (Fig. 7)
Switch action (Fig. 8)
CAUTION:
Before plugging in the tool, always check to see that
the tool is switched off.
To start the tool, push the switch lever on the left side
of the tool. To stop the tool, push the switch lever on
the right side of the tool.
Speed change (Fig. 9)
For HM1202C only
The blows per minute can be adjusted between 950
and 1,900 BPM just by turning the adjusting dial. This
can be done even while the tool is running. The dial is
marked 1 (lowest speed) to 6 (full speed). Refer to
the table below for the relationship between the num-
ber settings on the adjusting dial and the blows per
minute.
Chipping / Scaling / Demolition (Fig. 10)
Hold the tool firmly with both hands. Turn the tool on
and apply slight pressure on the tool so that the tool
will not bounce around, uncontrolled. Pressing very
hard on the tool will not increase the efficiency.
Indicator lamp (Fig. 11)
For HM1202C only
The green power-ON indicator lamp lights up when
the tool is switched ON. If the indicator lamp is lit but
the tool does not start, the carbon brushes may be
worn out, or the electric circuit or the motor may be
defective. If the indicator lamp does not light up and
the tool does not start, the ON/OFF switch or the
mains cord may be defective.
The red service indicator lamp lights up when the
carbon brushes are nearly worn out to indicate that
the tool needs servicing. After approx. 8 hours of use,
the motor will automatically be shut off.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Replacement of carbon brushes (Fig. 12 & 13)
Whenever carbon brushes must be replaced, they
cut out the tool automatically. When this occurs,
loosen the screws which secure the rear cover. Pry
up the rear cover with a screwdriver and remove it.
Then replace both carbon brushes at the same time.
Use only identical carbon brushes.
Lubrication
This tool requires no hourly or daily lubrication
because it has a grease-packed lubrication system.
Lubricate the tool every time the carbon brushes are
replaced.
Run the tool for several minutes to warm it up. Switch
off and unplug the tool.
Loosen the six screws and remove the handle.
(Fig. 14)
Remove the crank cap using a socket wrench.
(Fig. 15)
Rest the tool on the table with the bit end pointing
upwards. This will allow the old grease to collect
inside the crank housing. Wipe out the old grease
inside and replace with a fresh grease (30 g). Use
only Makita genuine hammer grease (optional acces-
sory). Filling with more than the specified amount of
grease (approx. 30 g) can cause faulty hammering
action or tool failure. Fill only with the specified
amount of grease. Reinstall the crank cap and tighten
with the socket wrench. (Fig. 16)
CAUTION:
Be careful not to damage the terminals or lead
wires especially when wiping out the old grease or
installing the handle.
Do not tighten the crank cap excessively. It is made
of resin and is subject to breakage.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by
a Makita Authorized Service Center.
Number on adjusting dial Blows per minute
6 1,900
5 1,800
4 1,600
3 1,300
2 1,050
1950
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita hm 1202 c at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita hm 1202 c in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita hm 1202 c

Makita hm 1202 c User Manual - German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info