Manual Makita HM 1140C (page 5 of 40) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

448481

Zoom out

Zoom in

1/40

ENGLISH

Explanation of general view

1 Bit grease

2 Bit shank

3 Tool holder cap

4 Tool holder cover

5 Cut in bit shank

6 Notch in tool holder cap

7 Change ring

8 Side handle

9 Can be swung 360° on the

vertical and secured at any

desired position

0 Secures at eight different

positions back and forth

on the horizontal

q Clamp nut

w Loosen

e Tighten

r ‘‘ON I’’ button

t ON

y OFF

u Adjusting dial

i Screwdriver

o Rear cover

p Screws

a Brush holder cap

s Socket wrench

d Crank cap

f Hammer grease

SPECIFICATIONS

Model HM1140C

Blows per minute ............................... 1,300 – 2,650

Overall length ............................................. 517 mm

Net weight ...................................................... 6.3 kg

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear pro-

tectors and thickly padded gloves.

2. Be sure the bit is secured in place before

operation.

3. Under normal operation, the machine is

designed to produce vibration. The screws

can come loose easily, causing a breakdown

or accident. Check tightness of screws care-

fully before operation.

4. In cold weather or when the machine has not

been used for a long time, let the machine

warm up for several minutes by operating it

under no load. This will loosen up the lubrica-

tion. Without proper warm-up, hammering

operation is difficult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the

machine in high locations.

6. Hold the machine firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the machine running. Operate the

machine only when hand-held.

9. Do not point the machine at any one in the

area when operating. The bit could fly out and

injure someone seriously.

10. When chipping into walls, floors or wherever

“live” electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE

MACHINE!

Hold the machine by the insulated grasping

surfaces to prevent electric shock if you chip

into a “live” wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing bit

Important:

Always be sure that the machine is switched off and

unplugged before installing or removing the bit.

This machine accepts 3/4″ Hexagonal and 21/32″

round shank bits. Clean the bit shank and apply the bit

grease provided to it before installing the bit. (Fig. 1)

Pull the tool holder cover down all the way. (Fig. 2-1)

With the cut in the bit shank aligned with the notch in

the tool holder cap, insert the bit into the tool holder.

(Fig. 2-2)

Release the tool holder cover. It will return automati-

cally to its original position to secure the bit. (Fig. 2-3)

After installing, always make sure that the bit is

securely held in place by trying to pull it out.

To remove the bit, pull the tool holder cover down all

the way and pull the bit out.

Bit angle (Fig. 3)

The bit can be secured at 12 different angles. To

change the bit angle, slide the change ring forward,

then turn the change ring to change the bit angle. At

the desired angle, slide the change ring back to the

original position. Then turn the change ring slightly so

that the bit will be secured in place with a little click.

HM1140C (E) (’98. 9. 7)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HM 1140C in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita HM 1140C

Makita HM 1140C User Manual - English, Dutch - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HM 1140C Manual

Product: