Manual Makita HM 1101C (page 7 of 44) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448480

Zoom out

Zoom in

1/44

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Lubrication

CAUTION:

• This servicing should be performed by Makita

Authorized Service Centers only.

This tool requires no hourly or daily lubrication because it

has a grease-packed lubrication system. It should be

lubricated every time the carbon brushes are replaced.

Send the complete tool to Makita Authorized Service

Center for this lubrication service. (Fig. 14)

Run the tool for several minutes to warm it up. Switch off

and unplug the tool.

Loosen the six screws and remove the handle. Note that

the top screws are different from other screws. (Fig. 15)

Disconnect the connector by pulling them. (Fig. 16)

Loosen the five screws on crank cap and remove the

crank cap. (Fig. 17)

Wipe out the old grease inside and replace with a fresh

grease (30 g). Use only Makita genuine hammer grease

(optional accessory). Filling with more than the specified

amount of grease (approx. 30 g) can cause faulty

hammering action or tool failure. Fill only with the

specified amount of grease.

CAUTION:

• Be careful not to damage the connector or lead wires

especially when wiping out the old grease.

To reassemble the tool, follow the disassembling

procedure in reverse.

CAUTION:

• Do not tighten the crank cap excessively. It is made of

resin and is subject to breakage.

• Be careful not to damage the connector or lead wires

especially when installing the handle. (Fig. 18)

Connect the connector firmly and then reinstall the

handle.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Bull point (SDS-max)

• Cold chisel (SDS-max)

• Scaling chisel (SDS-max)

• Clay spade (SDS-max)

• Bit grease

• Safety goggles

• Hammer grease

• Plastic carrying case

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Model HM1111C

Sound pressure level (L

): 88 dB (A)

Sound power level (L

): 99 dB (A)

Uncertainty (K): 3 dB (A)

Model HM1101C

Sound pressure level (L

): 90 dB (A)

Sound power level (L

): 101 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Model HM1111C

Work mode: chiseling function with side handle

Vibration emission (a

h,CHeq

): 7.5 m/s

Uncertainty (K): 1.5 m/s

Work mode: chiseling function with side grip

Vibration emission (a

h,CHeq

): 8.0 m/s

Uncertainty (K): 1.5 m/s

Model HM1101C

Work mode: chiseling function with side handle

Vibration emission (a

h,CHeq

): 13.5 m/s

Uncertainty (K): 2.0 m/s

Work mode: chiseling function with side grip

Vibration emission (a

h,CHeq

): 13.5 m/s

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

For European countries only

ENH101-14

EC Declaration of Conformity

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machine(s):

Designation of Machine:

Demolition Hammer

Model No./ Type: HM1111C, HM1101C

are of series production and

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HM 1101C in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HM 1101C Manual

Product: