448478

Makita HM 1100C Manual

5
Zoom out
Zoom in
Previous page
1/8
Next page
5
ENGLISH
Explanation of general view
1Bit grease
2 Bit shank
3Bit
4 Tool holder cover
5 Change ring
6 Side handle
7 Can be swung 360° on the
vertical and secured at any
desired position
8 Secures at eight different
positions back and forth
on the horizontal
9 Clamp nut
10 Loosen
11 Tighten
12 “ON I” button
13 ON
14 OFF
15 Adjusting dial
16 Screwdriver
17 Rear cover
18 Screws
19 Brush holder cap
20 Socket wrench
21 Crank cap
22 Hammer grease
SPECIFICATIONS
Model HM1100 HM1100C
Blows per minute ................................................................. 2,650 1,300 – 2,650
Overall length ....................................................................... 524 mm 524 mm
Net weight ............................................................................ 6.1 kg 6.1 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
ADDITIONAL SAFETY RULES
1. Wear a hard hat (safety helmet), safety
glasses and/or face shield. It is also highly
recommended that you wear a dust mask, ear
protectors and thickly padded gloves.
2. Be sure the bit is secured in place before
operation.
3. Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or acci-
dent. Check tightness of screws carefully
before operation.
4. In cold weather or when the tool has not been
used for a long time, let the tool warm up for
several minutes by operating it under no
load. This will loosen up the lubrication.
Without proper warm-up, hammering opera-
tion is difficult.
5. Always be sure you have a firm footing.
Be sure no one is below when using the tool
in high locations.
6. Hold the tool firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the tool running. Operate the
tool only when hand-held.
9. Do not point the tool at any one in the area
when operating. The bit could fly out and
injure someone seriously.
10. When chipping into walls, floors or wherever
‘‘live’’ electrical wires may be encountered,
DO NOT TOUCH ANY METAL PARTS OF THE
TOOL!
Hold the tool by the insulated grasping sur-
faces to prevent electric shock if you chip
into a ‘‘live’’ wire.
11. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing bit
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Clean the bit shank and apply the bit grease provided
to it before installing the bit. (Fig. 1)
Pull the tool holder cover down all the way and insert
the bit into the tool holder. (Fig. 2-1)
Turn the bit and push it in until it engages. (Fig. 2-2)
Release the tool holder cover. It will return automati-
cally to its original position to secure the bit.
(Fig. 2-3)
After installing, always make sure that the bit is
securely held in place by trying to pull it out.
To remove the bit, pull the tool holder cover down all
the way and pull the bit out.
Bit angle (Fig. 3)
The bit can be secured at 16 different angles. To
change the bit angle, slide the change ring forward,
then turn the change ring to change the bit angle. At
the desired angle, slide the change ring back to the
original position. Then turn the change ring slightly
so that the bit will be secured in place with a little
click.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HM 1100C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HM 1100C in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita HM 1100C

Makita HM 1100C User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info