Manual Makita hm 0860 c (page 6 of 14) (English, Dutch)

388903

Zoom out

Zoom in

1/14

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the tool is switched off.

To start the tool, push the “I (ON)” side of the switch lever.

To stop the tool, push “O (OFF)” side of the switch lever.

Speed change (Fig. 2)

The blows per minute can be adjusted just by turning the

adjusting dial. This can be done even while the tool is

running. The dial is marked 1 (lowest speed) to 5 (full

speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the blows per

minute.

CAUTION:

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

Indicator lamp (Fig. 3)

The green power-ON indicator lamp lights up when the

tool is plugged. If the indicator lamp is lit but the tool does

not start even if the tool is switched on, the carbon

brushes may be worn out, or the electric circuit or the

motor may be defective. If the indicator lamp does not

light up and the tool does not start, the electric circuit or

the mains cord may be defective.

The red service indicator lamp lights up when the carbon

brushes are nearly worn out to indicate that the tool

needs servicing. After approx. 8 hours of use, the motor

will automatically be shut off.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

For tool with side grip (auxiliary handle) (Fig. 4)

The side grip swings around to either side, allowing easy

handling of the tool in any position. Loosen the side grip

by turning it counterclockwise, swing it to the desired

position and then tighten it by turning clockwise.

Side handle (auxiliary handle) (Fig. 5)

The side handle can be swung 360° on the vertical and

secured at any desired position. It also secures at eight

different positions back and forth on the horizontal. Just

loosen the clamp nut to swing the side handle to a

desired position. Then tighten the clamp nut securely.

Bit grease (optional accessory)

Coat the bit shank head beforehand with a small amount

of bit grease (about 0.5 – 1 g). This chuck lubrication

assures smooth action and longer service life.

Installing or removing the bit (Fig. 6, 7 & 8)

Clean the bit shank and apply bit grease before installing

the bit.

Insert the bit into the tool. Turn the bit and push it in until

it engages.

If the bit cannot be pushed in, remove the bit. Pull the

chuck cover down a couple of times. Then insert the bit

again. Turn the bit and push it in until it engages.

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the way

and pull the bit out.

Bit angle (Fig. 9)

The bit can be secured at 12 different angles. To change

the bit angle, slide the change ring forward, then turn the

change ring to change the bit angle. At the desired angle,

slide the change ring back to the original position. The bit

will be secured in place.

OPERATION

CAUTION:

• Always use the side grip (auxiliary handle) and firmly

hold the tool by both side grip and switch handle during

operatioin.

Chipping/Scaling/Demolition (Fig. 10)

Hold the tool firmly with both hands. Turn the tool on and

apply slight pressure on the tool so that the tool will not

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

Replacing carbon brushes (Fig. 11, 12 & 13)

When the resin insulating tip inside the carbon brush is

exposed to contact the commutator, it will automatically

shut off the motor. When this occurs, both carbon

brushes should be replaced. Keep the carbon brushes

clean and free to slip in the holders. Both carbon brushes

should be replaced at the same time. Use only identical

carbon brushes.

Use a screwdriver to remove the brush holder covers.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

Reinstall the brush holder covers firmly.

Number on adjusting dial Blows per minute (min

–1

)

52,650

42,450

31,900

21,350

11,100

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita hm 0860 c in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita hm 0860 c

Makita hm 0860 c User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita hm 0860 c Manual

Product: