78430

Makita HK 1810 Manual

4
Zoom out
Zoom in
Previous page
1/7
Next page
ENGLISH
Explanation of general view
1 Dust cover
2 Tool retainer
3 Switch trigger
4 Speed control screw
5 Higher
6 Lower
7 Rear cover
8 Screwdriver
9 Brush holder cap
0 Lock nut wrench
q Crank cap
w Hammer grease
SPECIFICATIONS
Model HK1800 HK1810
Blows per minute ................................................................................................ 3,200 0 – 3,200
Overall length ...................................................................................................... 315 mm 315 mm
Net weight ........................................................................................................... 3.2 kg 3.2 kg
•
Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
•
Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only beoperated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
These symbols mean:
Read instruction manual.
DOUBLE INSULATION
ADDITIONAL SAFETY RULES
1. Wear a hard hat (safety helmet) and an ear
protector if necessary.
2. Be sure the scaling chisel is secured in place
before operation.
3. Under normal operation, the machine is
designed to produce vibration. The screws
can come loose easily, causing a breakdown
or accident. Check tightness of screws care-
fully before operation.
4. In cold weather or when the machine has not
been used for a long time, let the machine
warm up for several minutes by operating it
under no load. This will loosen up the lubrica-
tion. Without proper warm-up hammering
operation is difficult.
5. Always be sure you have a firm footing. Be
sure no one is below when using the machine
in high locations.
6. Hold the machine firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the machine running. Operate the
machine only when hand-held.
9. Do not point the machine at any one in the
area when operating. The scaling chisel or bull
point could fly out and injure someone seri-
ously.
10. When chipping into walls, floors or wherever
‘‘live’’ electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE
MACHINE!
Hold the machine only by the plastic handle or
the side grip to prevent electric shock if you
chip into a ‘‘live’’ wire.
11. Do not touch the scaling chisel immediately
after operation; they may be extremely hot and
could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing scaling chisel or other
bit (bull point, etc.) (Fig.1&2)
Important:
Always be sure that the machine is switched off and
unplugged before installing or removing the bit.
To install the bit, first attach the dust cover provided to
the bit as shown in Fig. 1.
Then turn the tool retainer in the direction of the arrow
and insert the bit into the machine barrel as far as it
will go. Now turn the tool retainer in the opposite
direction to secure the bit.
To remove the bit, follow the installation procedure in
reverse.
4
HK1800/HK1810 (E) (’97. 3. 6)
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HK 1810 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HK 1810 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita HK 1810

Makita HK 1810 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info