78357

Makita HK 0500 Manual

5
Zoom out
Zoom in
Previous page
1/36
Next page
Bit angle (Fig. 4)
The bit can be secured at 12 different angles. To
change the bit angle, slide the change ring forward,
then turn the change ring to change the bit angle. At
the desired angle, slide the change ring back to the
original position. The bit will be secured in place.
Switch action (Fig. 5)
CAUTION:
Before plugging in the machine, always check to see
that the switch trigger actuates properly and returns to
the ‘‘OFF’’ position when released.
To start the machine, simply pull the trigger. Release
the trigger to stop.
Speed change (Fig. 5)
The blows per minute can be adjusted between 2,000
and 3,500 BPM just by turning the adjusting dial. This
can be done even while the machine is running. The
dial is marked 1 (lowest speed) to 6 (full speed). Refer
to the table below for the relationship between the
number settings on the adjusting dial and the blows
per minute.
Number on adjusting dial Blows per minute
6 3,500
5 3,200
4 2,900
3 2,600
2 2,300
1 2,000
Operation
Position the bit at the location to be chipped, then pull
the trigger.Apply slight pressure on the machine so
that the machine will not bounce around, uncon-
trolled. Pressing very hard on the machine will not
increase the efficiency.
NOTE:
When removing tiles with a scaling chisel, apply the
chisel to the bottom of tiles as shown in Fig. 6.Ifyou
operate the machine with the chisel applied to the top
surface of tiles, the service life of the chisel will be
shortened. (Fig. 6)
MAINTENANCE
CAUTION:
Always be sure that the machine is switched off and
unplugged before carrying out any work on the
machine.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by
Makita Authorized Service Center.
HK0500 (E) (’98. 9. 18)
5
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HK 0500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HK 0500 in the language / languages: German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita HK 0500

Makita HK 0500 User Manual - English, Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info