Manual Makita HK 0500 (page 3 of 12) (English, Dutch)

78357

Zoom out

Zoom in

1/12

ENGLISH

Explanation of general view

1Bit

2Chuck cover

3 Change ring

4 Switch trigger

5 Adjusting dial

6 Tile

7 Scaling chisel

SPECIFICATIONS

Model HK0500

Blows per minute ....................................... 2,000 – 3,500

Overall length ..................................................... 468 mm

Net weight .............................................................. 3.1 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without prior notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to enclosed the safety

instructions.

SPECIFIC SAFETY RULES

GEB004-2

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to hammer safety rules. If you use this tool unsafely

or incorrectly, you can suffer serious personal injury.

1. Wear ear protectors. Exposure to noise can cause

hearing loss.

2. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

3. Hold tools by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring or its own cord. Con-

tact with a “live” wire will make exposed metal parts

of the tool “live” and shock the operator.

4. Wear a hard hat (safety helmet), safety glasses

and/or face shield. Ordinary eye or sun glasses

are NOT safety glasses. It is also highly recom-

mended that you wear a dust mask and thickly

padded gloves.

5. Be sure the bit is secured in place before opera-

tion.

6. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

7. In cold weather or when the tool has not been

used for a long time, let the tool warm up for a

while by operating it under no load. This will

loosen up the lubrication. Without proper warm-

up, hammering operation is difficult.

8. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

9. Hold the tool firmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

13. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

14. Do not operate the tool at no-load unnecessarily.

15. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

OPERATING INSTRUCTIONS

Installing or removing bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Clean the bit shank before installing the bit. Insert the bit

into the tool.Turn the bit and push it in until it engages.

(Fig. 1)

If the bit cannot be pushed in, remove the bit. Pull the

chuck cover down a couple of times. Then insert the bit

again. Turn the bit and push it in until it engages. (Fig. 2)

After installing, always make sure that the bit is securely

held in place by trying to pull it out. To remove the bit, pull

the chuck cover down all the way and pull the bit out.

(Fig. 3)

Bit angle (Fig. 4)

The bit can be secured at 12 different angles. To change

the bit angle, slide the change ring forward, then turn the

change ring to change the bit angle. At the desired angle,

slide the change ring back to the original position. The bit

will be secured in place.

Switch action (Fig. 5)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HK 0500 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita HK 0500

Makita HK 0500 User Manual - German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 36 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HK 0500 Manual

Product: