599736

Makita HG 1100 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
Makita Limited One
Year
Warranty
Warranty
Policy
Every Makita
tool
is thoroughly inspected and tested before leaving the factory.
It
is warranted
to
be
free of defects from workmanship and materials for the period of
ONE
YEAR
from the date of original
purchase. Should any trouble develop during this one-year-period, return the COMPLETE
tool,
freight
prepaid, to one of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is
caused
by defective workmanship or material, Makita will repair (or, at our option, replace) without
charge.
This Warranty does not apply where:
0
repairs have been made or attempted by others
0
repairs are required because of normal wear and tear
0
the
tool
has been abused, misused or improperly maintained
0
alterations have been made to the
tool
In no event shall Makita be liable for any indirect, incidental or consequential
damages from the sale or use
of
the product. This disclaimer applies both du-
ring and after the term of warranty.
Makita disclaims liablity for any implied warranties, including implied warranties
of
"merchantability" and "fitness for a specific purpose", after the one-year
term
of
this warranty.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to
state. Some states do not allow the exclusion or limitation of incidental or consquential damages,
so
the above limitation or exclusion may not apply
to
you. Some states do not allow limitation on how
long an implied warranty lasts,
so
the above limitation my not apply
to
you.
1.
This heat gun can produce up
to
llOOo
F
of fla-
meless heat at the nozzle. Do not direct air
stream at clothing, hair, or other body parts.
Do
not use as a hair dryer.
2. Do not use near flammable liquids or in an ex-
plosive environment (fumes, gases or dust).
Remove materials or debris that may become
ignited, from work area.
3.
Always hold tool by plastic enclosure. The me-
tal
nozzle requires approximately 20 minutes
to cool to where
it
can be touched.
Do
not
touch nozzle or accessory tips until cool.
4.
Do
not store tool until nozzle has cooled
to
room temperature. Place tool in a clear area
away from combustible materials while cool-
ing. Store indoors.
5.
Do
not cut
off
air flow. Keep cool air inlets
clean and clear of obstructions.
6. Place
tool
on a level surface when tool is not
hand held. Place cord in a position that won't
cause tipping, or tripping.
7. Do not leave tool unattended while running or
cooling down.
8. Keep a fully charged fire extinguisher nearby.
9.
Do
not direct air flow directly on glass.
10.
Shield materials around the heated area to pre-
11.
Use only with 120
Volts
A.C.
12. Do not use in wet conditions.
13.
The voltage from the power source must match
that specified on the nameplate.
14.
Not
to
be used by children. This is not a toy
and must be respected.
15. Do not use in bath or near water.
16. Safety glasses complying with current national
standards should be worn when using this
tool.
17.
For stripping paint see detailed instructions in
this manual.
18.
It
is recommended that gloves be worn when
using a Heat Gun.
vent damage or fire.
Double insulated tools, like this one, have
two
prong cords, and can use either a
two
or three
prong extension cord. As the distance from the
supply outlet increases, however, heavier gauge
extension cords are required. The use of extension
cords of inadequate size wire causes a serious
drop in voltage and
loss
of power. Protect the cord
from damage. Keep cords away from excessive
heat, sharp edges and damp or wet areas. Repair
or replace damaged extension cords before using.
Ext
Cord Lgth. Wire Size
40
Ft.
16
65
Ft.
14
100 Ft.
12
170
Ft.
10
270
Ft.
8
400
Ft.
6
650
Ft.
4
Hints
on
us88
for
Ths
Mrklb
HG
1100
oun
Forming and shaping plastic materials
0
Soften
PVC
pipe and
other
plastic materials
Soften
Vinyl
Floor
coverings
and
around
0
Soften,
plastic
laminate
coverings
for shap-
Welding plastic materials
(Caution: When attempting plastic welding, experi-
ment on scrap material beforehand.)
0
Welding
plastic
parts
on
automobiles
0
Welding leaking
PVC
plumbing pipes
and
joints
0
Lap-welding
PVC
sheet materials
0
Repairing household
items
made
of
WC
and
welding
PVC
flooring materials
0
Repairing sprinkler
system
PVC
pipes
(Detailed instructions for plastic welding are on the
Makita welding rod packages.)
Roofing
0
Heat
welding
of
single
ply
roofing
membra-
nes
0
Heating roofing
tar
and
roofing
cement
Glueing and removal
of
adhesives
0
Activating
heat
sensitive
adhesives
0
Removal of stickers from
automobile
bump-
Softening
and
removal
of
adhesives
Soldering
0
Soldering and desoldering copper pipe up
to
314"
0
De-soldering
components
on
PC
boards
0
Activate
solder
and
wire
connectors
Drying
0
Drying
paint
samples
0
Drying
plaster
filling
compounds
Shrinking
0
Shrinking
tube
insulators
0
Heat shrink packaging
wrap
Thawing
0
Thaw
frozen
water
pipes
0
Thaw frozen
locks
Other uses
0
Speed setting of fiberglass
fillers
Wax
removal
on
skies
and surfboards
0
Apply hot patches
0
Paint
stripping
0
Softening
hardened
window
glazing
for bending and shaping
mouldings.
ing rounded bends
on
countertops
ers and
windows
For Specific Tasks
WARNING:
Always unplug the
tool
before atta-
ching or removing accessories.
Do
not remove ac-
cessory tips until the
tool
has cooled
to
room tem-
perature.
Plastic Welding Nozzle
Attached to Item
No.
110706-A
to
provide concentrated
air flow
to
meR
the
plastic welding rod. Also,
can be used for fusing
plastic parts together
Item
No.
110
720-A
Plastic Welding
Rods
Used
to
provide filler material for
welding operation. Caution: be
sure welding rod material matches
material being welded. Rods are
approx
9
long and
1/8"
in dia.
with
16
pcs. per package.
PVC
plastic
item
No.
110
731
-A
ABS plastic
item
No.
110
742-A
3/8"
Reduction Nozzle
Provides small area air
flow (approx
3/87.
Also,
used
with
Item
No.
110720-A
for
plastic
welding.
Item
No.
110
706-A
3/8"
Reflector Nozzle
Small reflector nozzle for
use in activating solder
sink wire connectors and
small shrink tubing.
Item
No.
110
746-A
Wide Angle Slit Nozzle
Provides a
1
314" x 3/16
air
flow.
Nozzle
has
a
slight
angle
to
direct
air flow for lap welding
surfaces such
as
WC
materials and single ply
roofing.
Item
No.
110
751-A
3"
Surface Nozzle
Provides a
3
by
1/4
air
flow for heating large
surfaces.
Item
No.
110
702-A
Large Reflector Nozzle
3"
Wide. Used
to
deflect
air flow aroung
pipes.
Used for bending
WC
pipe,
heat
shrinking
tubing, thawing pipe and
soldering copper
pipe.
Item
No.
110730-A
Available at your Makita dealer
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HG 1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HG 1100 in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info