599701

Makita GN420C Manual

8
Zoom out
Zoom in
Previous page
1/72
Next page
8
Overview of the nailer
1
2
3
4
5
6
7
8
9
10
013150
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure to remove the fuel cell, the battery
cartridge and nails before adjusting or checking
function on the tool.
Installing or removing battery cartridge
CAUTION:
• Always switch off the tool before installing or
removing of the battery cartridge.
• Hold the tool and the battery cartridge firmly
when installing or removing battery cartridge.
Failure to hold the tool and the battery cartridge
firmly may cause them to slip off your hands and
result in damage to the tool and battery cartridge
and a personal injury.
Fig.1
To install the battery cartridge, hold it so that the battery
cartridge front shape fits to that of the battery
installment opening and slip it into place. Insert it all the
way until it locks in place with a little click.
Fig.2
To remove the battery cartridge, withdraw it from the
tool while pressing the both sides of the cartridge.
CAUTION:
• Always insert the battery cartridge all the way until
it locks in place. If not, it may accidentally fall out
of the tool, causing injury to you or someone
around you.
• Do not install the battery cartridge forcibly. If the
cartridge does not slide in easily, it is not being
inserted correctly.
Lighting up the lamp
CAUTION:
• Do not look in the light or see the source of light
directly.
Fig.3
• To switch on the Lamp, press the lamp button. To
switch off the lamp, press the lamp button again.
Fuel cell
Attaching the metering valve to the fuel cell
Fig.4
Detach the cap (in case the metering valve is provided
with the cap).
Fig.5
Push in the front edge.
Fig.6
Push in the rear edge until it seats.
Inserting the fuel cell
Fig.7
Push up and pull the fuel cover to open.
Fig.8
Insert the fuel cell directing the jet nozzle of the
metering valve toward the adaptor.
Fig.9
Insert the jet nozzle into the small hole of the adapter
properly.
Fig.10
Put the fuel cover over the metering valve and push it
down to latch.
Adjusting the nailing depth
CAUTION:
• Remove the fuel cell, the battery cartridge and
nails before adjusting the depth of nailing.
Fig.11
To get shallower depth, turn the adjuster to right
direction as shown in the figure. To get deeper depth,
turn the adjuster to left direction.
Do not turn the adjuster too much, or the adjuster may
get stuck.
1. Fuel cover
2. Trigger
3. Magazine
4. Pusher lever
5. Pusher button
6. Contact element
7. Exhaust vent
8. Lamp
9. Indicating lamp
10. Battery cartridge
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita GN420C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita GN420C in the language / languages: English, German, Polish as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info