Manual Makita GB801 (page 8 of 80) (English, German, Dutch, French, Italian, Polish, Spanish)

448453

Zoom out

Zoom in

1/80

1. Saw blade

2. Screw

3. Grinding wheel

4. Wing nut A

5. Holder A

Loosen the wing nut B and slide the holder B so that the

“gullet” or slot between the saw blade Teeth just comes in

contact with the edge of the Wheel. Slide the stopper so

that it comes in contact with the holder B and tighten the

wing nut B securely.

WARNING:

Always disconnect the bench grinder from the power

source before performing any assembly or adjustment.

Failure to do so could result in accidental starting resulting

in possible serious personal injury.

WHEEL REPLACEMENT

See Fig.13.

If you must replace a grinding wheel, be sure to obtain

one with a safe rated speed at least as high as the “no

load speed” RPM marked on the data plate of the grinder

and which is marked to comply with EN12413.

To replace the grinding wheel, remove the wheel cover by

loosening the screws with holding the nut wrench.

Loosen the wheel nut in a clockwise direction for the left

side and a counterclockwise direction for the right side

using the correct wrench. Remove the outer flange and

grinding wheel. To install a new grinding wheel, reverse

the above procedure.

Be sure the grinding wheel and outer flange are properly

seated on the spindle shaft.

1. Wrench

2. Wheel cover

1. Wrench 13

2. Wrench 19

GB801 only

1. Wrench 17

2. Wrench 24

WARNING:

When servicing, use only manufacturers recommended

replacement parts. Use of other part may create a hazard

and cause product damage.

GENERAL

Keep the bench grinder clean. Remove dust from working

parts and beneath the grinder frequently.

Make sure the bench grinder operates properly. Check

screws, nuts, and bolts for tightness.

EXTENSION CORDS

The use of any extension cord will cause some loss of

power. To keep the loss to a minimum and to prevent tool

overheating, use an extension cord that is heavy enough

to carry the current the tool will draw.

An extension lead of cross sectional area of at least

1.5 mm

is recommended for an extension cord 8 meters

or less in length. When working outdoors, use an

extension cord that is suitable for outdoor use.

WARNING:

Check extension cords before each use. If damaged,

replace immediately. Never use tool with damaged cord

since touching the damaged area could cause electrical

shock resulting in serious injury.

WORKLIGHT BULB REPLACEMENT

1. Light bulb

When the light bulb is worn out and no longer working,

unfasten the screws which fix the lamp cover, then gently

remove the bulb from the holder by pushing in and turning

anticlockwise. Contact your dealer for replacement part.

To replace, gently push the light bulb into the insert and

turn clockwise, then fix the lamp cover in the revise order.

WHEEL DRESSING TOOL (Accessory)

Dressing a wheel is done to renew sharpness or to true up

the face of the wheel.

Set the work rest of the bench grinder at a slight angle

and brace the wheel-dressing tool against it. Do not make

contact with the grinding wheel until after you have turned

on the motor and the wheel is rotating at full speed. Press

the dressing tool slightly against the rotating wheel until

you get a bite, then move slowly from side to side across

the wheel. A small bite and many passes are better than a

big bite and one pass. Work cautiously; hold the dresser

with force on the work rest. Do not use excessive

pressure against the grinding wheel. Proceed slowly until

you master the technique.

Fig. 12

Fig. 13

Fig. 14

MAINTENANCE

Fig. 15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita GB801 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita GB801 Manual

Product: