Manual Makita GA9061 (page 6 of 100) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691764

Zoom out

Zoom in

1/100

6 ENGLISH

Work mode: disc sanding with normal side grip

Vibration emission (a

h, DS

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

Work mode: disc sanding with anti vibration side grip

Vibration emission (a

h, DS

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

Model GA9061R

Work mode: surface grinding with normal side grip

Vibration emission (a

h, AG

) : 6.5 m/s

Uncertainty (K) : 1.5 m/s

Work mode: surface grinding with anti vibration side grip

Vibration emission (a

h, AG

) : 5.5 m/s

Uncertainty (K) : 1.5 m/s

Work mode: disc sanding with normal side grip

Vibration emission (a

h, DS

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

Work mode: disc sanding with anti vibration side grip

Vibration emission (a

h, DS

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

NOTE: The declared vibration emission value has

been measured in accordance with the standard test

method and may be used for comparing one tool with

another.

NOTE: The declared vibration emission value

may also be used in a preliminary assessment of

exposure.

WARNING: The vibration emission during actual

use of the power tool can differ from the declared

emission value depending on the ways in which the

tool is used.

WARNING: Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it is

running idle in addition to the trigger time).

WARNING: The declared vibration emission

value is used for main applications of the power tool.

However if the power tool is used for other applica-

tions, the vibration emission value may be different.

EC Declaration of Conformity

For European countries only

Makita declares that the following Machine(s):

Designation of Machine: Angle Grinder

Model No./ Type: GA7061, GA7061R, GA9061,

GA9061R

Conforms to the following European Directives:

2006/42/EC

They are manufactured in accordance with the following

standard or standardized documents: EN60745

The technical le in accordance with 2006/42/EC is

available from:

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

17.6.2015

Yasushi Fukaya

Director

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

General power tool safety warnings

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Grinder safety warnings

Safety Warnings Common for Grinding, Sanding,

Wire Brushing, or Abrasive Cutting-Off Operations:

1. This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool.

Read all safety warnings, instructions, illus-

trations and specications provided with this

power tool. Failure to follow all instructions listed

below may result in electric shock, re and/or

serious injury.

2. Operations such as polishing are not rec-

ommended to be performed with this power

tool. Operations for which the power tool was not

designed may create a hazard and cause per-

sonal injury.

3. Do not use accessories which are not speci-

cally designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and y apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

6. Threaded mounting of accessories must

match the grinder spindle thread. For acces-

sories mounted by anges, the arbour hole of

the accessory must t the locating diameter

of the ange. Accessories that do not match the

mounting hardware of the power tool will run out of

balance, vibrate excessively and may cause loss

of control.

7. Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install

an undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum

no-load speed for one minute. Damaged acces-

sories will normally break apart during this test

time.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita GA9061 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 17,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita GA9061 Manual

Product: