448427
5
Zoom out
Zoom in
Previous page
1/80
Next page
5
ENGLISH (Original instructions)
Explanation of general view
1 Shaft lock
2 Switch trigger
3 Lock lever
4 Indication lamp
5 Side grip
6 Wheel guard
7Screw
8 Bearing box
9Nut
10 Lever
11 Lock nut
12 Depressed center grinding
wheel/Multi-disc
13 Inner flange
14 Super flange
15 Depressed center wheel/
Multi disc
16 Lock nut wrench
17 Shaft lock
18 Abrasive disc
19 Rubber pad
20 Wire cup brush
21 Wire wheel brush
22 Abrasive cut-off wheel/diamond
wheel
23 Wheel guard for abrasive cut-off
wheel/diamond wheel
24 Outer flange 78
25 Inner flange 78
26 Exhaust vent
27 Inhalation vent
28 Commutator
29 Insulating tip
30 Carbon brush
31 Screwdriver
32 Brush holder cap
SPECIFICATIONS
Model GA7012C GA9012C
Depressed center wheel diameter................................................180 mm 230 mm
Spindle thread ..............................................................................M14 M14
No load speed (n
0
) / Rated speed (n)...........................................8,400 min
–1
6,000 min
–1
Overall length ...............................................................................453 mm 453 mm
Net weight.....................................................................................4.3 kg 4.5 kg
Safety class .................................................................................. /II /II
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
GEA010-1
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
GEB033-3
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Operations such as polishing are not recom-
mended to be performed with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
6. The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of
the power tool will run out of balance, vibrate exces-
sively and may cause loss of control.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita GA7012C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita GA7012C in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info