448423

Makita G 1700i Manual

9
Zoom out
Zoom in
Previous page
1/24
Next page
2. COMPONENTS (See Fig.
11
)
3.
CONTROLS AND INDICATORS
(See Fig.
22
)
1. ENGINE SWITCH (See Fig.
22
-
qq
)
Please refer to the illustrations on the back
page of
the front cover or back cover for
Fig.
11
to
66
indicated in the sentence.
NOTE
q RECOIL STARTER (HANDLE)
w CONTROL PANEL
e SIDE PANEL (L)
r AIR CLEANER
t FUEL DRAIN SCREW
y CARRYING HANDLE
u TANK CAP COVER
i EXHAUST OUTLET
o OIL DRAIN PLUG
!0 SIDE PANEL (R)
!1 OIL GAUGE (OIL FILLER)
!2 SPARK PLUG CAP
The engine switch is designed for easy operation
with the interlocking mechanism between the fuel
cock and the choke furnished.
When the engine stops due to oil shortage, it can
not be started anymore even by pulling the start
knob (just the alarm lamp flickers). In such a case,
replenish engine oil up to the mouth of the oil filling
port.
(Refer to page 6 for details about the oil
replenishing procedure).
The AUTO POWER SAVE LAMP is turned on when
the switch is in the “ON” position.
With the switch in the “ ” marking position, the
engine speed is reduced automatically when no
electricity is taken out, while the engine speed is
automatically adjusted in accordance with the load
condition when the electricity is taken out.
When using in the heavy load condition, set the
switch into the “ ” marking position to maintain
the electric power level in the stable condition.
When using DC power, turn the switch into the
“OFF” position.
5
ENGLISHFRANÇAISEESPAÑOL
5. AC RECEPTACLES
AC electric power is available through this receptacle.
Use a ground type, three-leg plug as shown.
CHOKE
To start the engine, turn the knob to the
position. (Choke valve is closed.)
RUN
Keep the knob in this position after the
engine starts. (The engine can be
started with the knob at this position
when the engine is warm.)
STOP
To stop the engine, return the knob to
the position.
(The fuel cock is closed as well.)
Do not plug more than two appliances
into the generator at a time.
Do not put foreign objects into the plug
receptacle.
CAUTION
6. AC CIRCUIT BREAKER
AC circuit breaker will cut off electric current when
the current exceeds its limit or a malfunction occurs
in the connected appliances.
Check for excessive current consumption or defects
in the appliances. After making sure everything is in
order, push the circuit breaker button.
If circuit breaker continues to be activated,
discontinue use and check generator
and/or appliance for
malfunction with
their respective service representatives.
Never interfere with the operation of the
circuit breaker knob or keep pushing it in
the "ON" position.
CAUTION
2. PILOT LAMP and OVERLOAD LAMP
(See Fig.
22
-
ww
)
These lamps are turned on in the following conditions;
PILOT LAMP (Green) --- The lamp is turned on
while generating properly.
OVERLOAD LAMP (Red) --- The lamp is turned on in the
overload condition.
* The breaker will be activated after the lamp is
turned on for 20 seconds in the 120% electric
power condition, and results in no load condition.
* If the lamp is turned on, stop and start the engine
again to resume the operation.
3. OIL SENSOR LAMP (See Fig.
22
-
ee
)
When the level of the engine oil falls below the
prescribed value, the alarm lamp lights up and the
engine stops automatically.
4.
AUTO POWER SAVE SWITCH AND LAMP
(See Fig.
22
-
rr
)
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita G 1700i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita G 1700i in the language / languages: English as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita G 1700i

Makita G 1700i User Manual - German - 21 pages

Makita G 1700i User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info