599912

Makita EY401MP Manual

9
Zoom out
Zoom in
Previous page
1/64
Next page
9
Maintenance schedule
Operating hour
Before
Operation
Daily
(10 h)
25 h 50 h
If
required
Corresponding page
Whole unit Visually inspect for
damaged parts
8
All xing screws and nuts Tighten
8
Chain oil feed port Clean
8
Guide bar Clean the groove and the
chain oil feed port
8
Visually inspect
8
Supply grease to the nose
8
Gear case Supply grease
8
Drive axle Supply grease
8
Sprocket Visually inspect
8
Saw chain Replace or ask for
sharpening
8
Power unit Refer to the instruction manual of the power unit
Troubleshooting
Problem Probable cause Solution
The motor does not start. Refer to the instruction manual of the power unit.
The motor stops soon after its start.
The maximum speed is limited.
The saw chain does not move.
Stop the motor immediately!
The guide bar is bent or damaged. Replace the guide bar.
A twig is caught by the saw chain. Remove the foreign matter.
The drive system does not work properly. Ask Makita authorized service center to
inspect and repair it.
The unit vibrates abnormally.
Stop the motor immediately!
The drive system does not work properly. Ask Makita authorized service center to
inspect and repair it.
The saw chain does not stop.
Stop the motor immediately!
The power unit does not work properly. Refer to the instruction manual of the power
unit.
Chain oil is not supplied. The oil tank is empty. Fill the oil tank with chain oil.
The chain-oil feed port is dirty. Clean the chain-oil feed port on the unit and
guide bar.
The adjusting screw of the chain-oil feed rate
is improperly set.
Set the adjusting screw properly.
Technical data
Model EY401MP
Dimensions (L x W x H) mm 1,166 x 74 x 105
Mass kg 1.0
Guide bar length mm 255 (10”)
Saw chain 91VXL-39E
Chain gauge inch 0.050”
Number of sprocket teeth 7
Chain oil Makita genuine chain oil
Chain oil pump Plunger pump
(Self lubricating type)
Chain oil tank capacity ml 120
Gear ratio (speed increasing) 0.94
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EY401MP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EY401MP in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info