599912

Makita EY401MP Manual

6
Zoom out
Zoom in
Previous page
1/64
Next page
6
Part description (Fig. 1)
The numbers below refer to the gure
1. Shaft
2. Gear Case
3. Oil cap
4. Oil tank
5. Bar holder
6. Guide bar
7. Saw chain
8. Guide bar cover
Safety precautions
WARNING: Read all safety warnings and all instructions
in this booklet and the instruction manual of the power unit.
Failure to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term “pole saw” and “equipment” in the warnings and
precautions refer to the combination of the attachment and the
power unit.
The term “motor” in the warnings and precautions refers to the
engine or electric motor of the power unit.
Intended use
This attachment is designed for only the purpose of pruning •
branches and limbs less than 15 cm in diameter in conjunction
with an approved power unit. Never use the attachment for the
other purpose. Abusing the attachment may cause serious injury.
General precautions
Before starting the pole saw, read this booklet and the instruction •
manual of the power unit to become familiar with the handling of
the pole saw.
Do not lend the attachment to a person with insufcient •
experience or knowledge regarding handling of pole saws.
When lending the attachment, always attach this instruction •
manual.
Do not allow children or young persons under 18 years old to use •
the pole saw. Keep them away from the pole saw.
Handle the pole saw with the utmost care and attention.•
Never use the pole saw after consuming alcohol or drugs, or if •
feeling tired or ill.
Never attempt to modify the attachment.•
National regulations may restrict of the use of the equipment.•
Follow the regulations about handling of pole saws and chain
saws in your country.
Personal protective equipment
Wear safety helmet, protective goggles and protective gloves to •
protect yourself from ying debris or falling objects. (Fig. 2)
Wear ear protection such as ear muffs to prevent hearing loss.•
Wear proper clothing and shoes for safe operation, such as •
a work overall and sturdy, non-slip shoes. Do not wear loose
clothing or jewelry. Loose clothes, jewelry or long hair can be
caught in moving parts.
When handling the saw chain or adjusting the chain tension, wear •
protective gloves. Saw chain can cut bare hands severely.
Work area safety
• Danger: Keep the pole saw at least 15 m away from electric
lines and communication cables (including any branches
contacting them). Touching or approaching high-voltage lines with
the pole saw can result in death or serious injury. Watch power
lines and electrical fences around the work area before starting
operation.
Operate the pole saw under good visibility and daylight conditions •
only. Do not operate the pole saw in darkness or fog.
Start and operate the engine only outdoors in a well ventilated •
area. Operation in a conned or poorly ventilated area can result
in death due to suffocation or carbon monoxide poisoning.
During operation, never stand on an unstable or slippery surface •
or a steep slope. During the cold season, beware of ice and snow
and always ensure secure footing.
During operation, keep bystanders or animals at least 15 m •
away from the pole saw. Stop the motor as soon as someone
approaches.
Before operation, examine the work area for wire fences, walls, •
or other solid objects. They can damage the saw chain.
• WARNING: Use of this product can create dust containing
chemicals which may cause respiratory or other illnesses.
Some examples of these chemicals are compounds found in
pesticides, insecticides, fertilizers and herbicides.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially
designed to lter out microscopic particles.
Putting into operation
Before assembling or adjusting the equipment, switch off the •
motor and remove the spark plug cap or the battery cartridge.
Before handling the saw chain or adjusting the chain tension, •
wear protective gloves.
Before starting the motor, inspect the equipment for damages, •
loose screws/nuts or improper assembly. Sharpen blunt saw
chain. If the saw chain is bent or damaged, replace it. Check all
control levers and switches for easy action. Clean and dry the
handles.
Never attempt to start the motor if the equipment is damaged or •
not fully assembled. Otherwise serious injury may result.
Adjust the shoulder harness and hand grip to suit the operator’s •
body size.
Adjust the chain tension properly. Rell the chain oil, if necessary.•
Starting motor
Wear the personal protective equipments before starting the motor.•
Start the engine at least 3 meters (10 feet) away from the fueling •
spot.
Before starting the motor, make sure that there is no person or •
animal in the work area.
When starting the engine or inserting a battery cartridge, keep •
the saw chain and guide bar clear of your body and other object,
including the ground. The saw chain may move when starting
and may cause serious injury or damage to the saw chain and/or
property.
Place the equipment on rm ground. Maintain good balance and •
secure footing.
When pulling the starter knob, hold the power unit rmly against •
the ground by your left hand. Never step on the drive shaft of the
power unit. (Fig. 3)
Follow the instruction manual of the power unit for starting the •
motor.
Check that there is sufcient difference between idling and •
engagement speed to ensure that the attachment is at a standstill
while the engine is idling (if necessary reduce idling speed).
If the saw chain moves at idle, stop the engine and adjust the idle •
speed down.
Operation
In the event of an emergency, switch off the motor immediately.•
If you feel any unusual condition (e.g. noise, vibration) during •
operation, switch off the motor. Do not use the equipment until
the cause is recognized and solved.
The saw chain continues to move for a short period after •
releasing the throttle trigger or switch off the motor. Don’t rush to
contact the saw chain.
With the engine running only at idle, attach the shoulder harness.•
During operation, use the shoulder harness. Keep the equipment •
on your right side rmly. (Fig. 4)
Hold the front handle with the left hand and the rear grip with the •
right hand, no matter you are right-hander or left-hander. Wrap
your ngers and thumbs around the handles.
Never attempt to operate the equipment with one hand. Loss of •
control may result in serious or fatal injury. To reduce the risk of
injury, keep your hands and feet away from the blades.
Do not overreach. Keep proper footing and balance at all times. •
Watch for hidden obstacles such as tree stumps, roots and
ditches to avoid stumbling. Clear fallen branches and other
objects away.
Never work on a ladder or tree to avoid loss of control.•
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EY401MP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EY401MP in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info