599913

Makita EY2650H Manual

6
Zoom out
Zoom in
Previous page
1/264
Next page
6
- Pay attention to the environment. Avoid unnecessary throttle operation for
less pollution and noise emissions. Adjust the carburetor correctly.
- During or after operation, do not put the hot equipment onto dry grass or
combustible materials.
- Do not hold your right hand above shoulder height.
- During operation, never hit the saw chain against hard obstacles such stones
and nails. Take particular care when cutting branches next to walls, wire
fences or the like.
- If branches get caught in the saw chain, always stop the engine and remove
the spark plug cap. Otherwise unintentional start may cause serious injury.
- If the saw chain becomes clogged, always stop the engine and remove the
spark plug cap before cleaning.
- Accelerating the engine with the saw chain blocked increases the load and
will damage the engine and/or clutch.
- Before cutting limbs, keep an escape area away from the falling limb. First,
clear obstructs such as limbs and branches from the work area. Move all
tools and goods from the escape area to another safe place.
- Before cutting branches and limbs, check the falling direction of them,
considering the condition of branches and limbs, adjoining trees, wind
direction, etc. Pay full attention to the falling direction, and the rebound of the
branch, which hit the ground.
- Never hold the pole saw at an angle of more than 60°. Otherwise falling
objects can hit the operator and cause serious injury. Never stand underneath
the limb being cut.
- Pay attention to broken or bent branches. They may bounce back in cutting,
causing unexpected injury.
- Before cutting limbs that you intend to cut, remove branches and leaves
around them. Otherwise the saw may be caught by them.
- To prevent the saw from being caught in the kerf, do not release the throttle
lever before pulling the saw out of the kerf.
- If the saw chain is bound in the kerf, immediately stop the engine, carefully
move the branch to open the kerf and release the saw.
- Avoid kickback (rotational reactive force towards the operator). To prevent
kickback, never use the guide bar nose or perform a penetrating cut. Always
beware of the position of the guide bar nose.
- Check the chain tension frequently. When checking or adjusting the chain
tension, stop the engine and remove the spark plug cap. If the tension is
loose, tighten it.
- Operate the equipment with as little noise and contamination as possible. In
particular check the correct setting of the carburetor.
- Never stand on a ladder and run the equipment.
- Never climb up into trees to perform cutting operation.
- Wait until the chain reaches its full working speed before cutting.
- Take a rest to prevent loss of control caused by fatigue. We recommend to
take a 10 to 20-minute rest every hour.
Transport
- Before transporting the equipment, switch off the engine and remove the
spark plug cap.
- $OZD\V¿WWKHJXLGHEDUFRYHUGXULQJWUDQVSRUWDWLRQ
- Always use the tool protection included with the equipment.
- &DUU\LWLQDKRUL]RQWDOSRVLWLRQE\KROGLQJWKHVKDIW.HHSWKHKRWPXIÀHU
away from your body.
- When transporting the equipment in a vehicle, properly secure it to avoid
turnover. Otherwise fuel spillage and damage to the equipment and other
baggage may result.
- Shut off the engine during transport.
- Ensure that the fuel tank is completely empty.
- When unloading the equipment from the truck, never drop the engine to the
ground or this may severely damage the fuel tank.
- Remember to lift the entire equipment from the ground when moving the
equipment. Dragging the fuel tank is highly dangerous and will cause damage
DQGOHDNDJHRIIXHOSRVVLEO\FDXVLQJ¿UH
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EY2650H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EY2650H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 8,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info