599909

Makita EW320TR Manual

28
Zoom out
Zoom in
Previous page
1/152
Next page
EN
3. INSPECTING THE SPARK PLUG
(See Fig.
77
77
7
-
qq
qq
q)
Clean off carbon deposits on the spark plug electrode using a plug cleaner or wire brush.
Check electrode gap. (See Fig.7 q q)
Adjust the gap, if necessary, by carefully bending the side electrode.
Use a proper spark plug
2. PERIODIC INSPECTION
Periodic maintenance is vital to the safe and efficient operation
of your product.
Check the table below for periodic maintenance intervals. The
below chart is based on the normal product operation
schedule.
Replace rubber pipes for fuel passage every two
years. If fuel leakage is found, replace the pipe
immediately.
CAUTION
Maintenance Items
Every
1000
hours
Every
500
hours
Every
200 hours
(Monthly)
Every
50 hours
(Weekly)
Every
8 hours
(Daily)
Clean pump set and check bolt and nuts
(Daily)
(Every 2 years)
Check and refill engine oil
Change engine oil (*Note 1)
Clean spark plug
Clean air cleaner
Replace air cleaner element
Clean fuel strainer
Remove carbon from cylinder head
(*Note 2)
Check and adjust valve clearance
(*Note 2)
Clean and adjust carburetor (*Note 2)
Replace fuel lines
*NOTE: 1. Initial oil change should be performed after first twenty (20) hours of operation.
Thereafter change oil every hundred (100) hours.
Before changing oil, check for a suitable way to dispose of old oil.
Do not pour it down into sewage drains, onto garden soil or into open streams. Your local zoning
or environmental regulations will give you more detailed instructions on proper disposal.
*NOTE: 2. As to the procedures for these items, please refer to the SERVICE MANUAL or consult your
nearest Makita service dealer.
Overhaul engine (*Note 2)
Clean and adjust spark plug and electrodes
Replace spark plug
Periodic Maintenance Schedule table
Check for leakage from hoses and fitting
(Daily)
(Refill daily up to upper level)
(Initial
20 hours)
(Every
100 hours)
Electrode gapModel
EW120R 0.7 to 0.8 mm
EW220R
EW220ST
EW320R
EW220TR
EW320TR
0.6 to 0.7 mm
Type
NGK CMR6A
NGK BR-6HS
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EW320TR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EW320TR in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info