Manual Makita EW3050H (page 14 of 32) (All languages)

690621

Zoom out

Zoom in

1/32

8. EASY TROUBLESHOOTING

1. PUMP DOES NOT RUN.

■

Engine dose not start.

(See “8.-6. WHEN ENGINE DOES NOT START”)

■

Sticking of impeller (Disassemble and clean.)

2. PUMPING VOLUME IS SMALL.

■

Sucking air at suction side.

(Check piping at suction side.)

■

Drop off engine output.

(Consult your nearest dealer.)

■

Breakage of mechanical seal.

(Consult your nearest dealer.)

■

High suction lift (Lower.)

■

Suction hose is too long or thin.

(Use a thick hose in minimum length.)

■

Leak of water from water passage. (Stop leaking.)

■

Clogging of foreign substance in impeller.

(Disassemble and clean.)

■

Wear of impeller.

■

Strainer is clogged. (Clean.)

■

Engine speed is too low.

(Consult your nearest dealer.)

3. PUMP DOES NOT SELFPRIME.

■

Suction of air at suction side.

(Check piping at suction side.)

■

Insufcient priming water inside pump casing.

(Prime fully.)

■

Imperfect tightening of drain plug.

(Tighten the plugs completely.)

■

Engine speed is too low.

(Consult your nearest dealer.)

■

Sucking air from mechanical seal.

(Consult your nearest dealer.)

4. DELIVERY HOSE DOES NOT STAY ON

COUPLING.

■

Hose may be kinked or discharge end may be

blocked or clogged. (Straighten or clean.)

5. PUMP SUDDENLY STOPS.

■

Solid object preventing pump-rod from completing

stroke. (Disassemble and clean.)

6. WHEN ENGINE DOES NOT START:

Perform the following checks before you take the pump

to your Makita dealer. If you still have trouble after

completing the checks, take the pump to your nearest

Makita dealer.

(1) Is there a strong spark across the electrode?

■

Is the stop switch at position “ I ” (ON)?

■

Remove and inspect the spark plug.

If the electrode is fouled, clean or replace it with

new one.

■

Remove the spark plug and connect it to the plug

cap. Pull the starter handle while grounding spark

plug against engine body. Try with a new spark plug

if the spark is weak or there is no spark.

The ignition system is faulty if there is no spark with

a new spark plug.

WARNING

■

Wipe out spilled fuel carefully before

testing. Place spark plug as far away from

spark plug hole as possible.

■

Do not hold spark plug by hand while

pulling recoil starter.

NOTE

The engine with oil sensor will stop automatically

when the oil level falls below the prescribed limit.

Unless the oil level is raised above the prescribed

limit, the engine will stop immediately after starting.

(2) Is there enough compression?

Pull the starter handle slowly and check if

resistance is felt.

If little force is required to pull the starter handle,

check if the spark plug is tightened rmly. If the

spark plug is loose, tighten it.

(3) Is the spark plug wet with gasoline?

■

Is the fuel valve opened?

■

Choke (close choke lever) and pull the starter

handle ve or six times. Remove the plug and

check if its electrode is wet. If the electrode is wet,

fuel is well supplied to your engine.

■

When the electrode is dry, check where the fuel

stops. (Check the fuel intake of the carburetor.)

■

In case the engine does not start with well supplied

fuel, try using fresh fuel.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita EW3050H in the language / languages: All languages as an attachment in your email.

The manual is 8,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita EW3050H Manual

Product: