599902
12
Zoom out
Zoom in
Previous page
1/37
Next page
12
OPEN
CLOSE
At times, such as winter, when starting the engine
is difcult
Operate choke lever with the following procedure when starting engine.
After implementing startup steps 1) to 3), set choke lever to the CLOSE
position.
Implement startup step 4) and start engine.
Once engine starts, set choke lever to the OPEN position.
Implement startup step 5) and complete warm up.
CAUTION: If a bang (explosive sound) is heard and the engine stops, or
the just-started engine stalls before the choke lever is operated,
return the choke lever to the OPEN position, and pull the starter
knob a few times again to start the engine.
CAUTION: If the choke lever is left in the CLOSE position, and the starter
knob merely pulled repeatedly, too much fuel will be sucked in,
and the engine will become difcult to start.
ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)
When it is necessary to adjust the low-speed rotation (idling), perform it by the carburetor adjusting screw.
CHECKUP OF LOW-SPEED ROTATION
Set the low-speed rotation to 3,000 min
-1
.
If it is necessary to change the low speed rotation (idle) speed, use a phillips
head screw driver on the screw illustrated on the right.
Turn the adjusting screw to the right, and the engine rotation will increase.
Turn the adjusting screw to the left, and the engine rotation will drop.
The carburetor is generally adjusted before shipment. After several tanks of
gasoline the idle rpm may need to be readjusted.
Carburetor
Adjusting
screw
STOPPING
1) Release the throttle lever (2) fully, and when the engine rpm has lowered,
set the I-O switch to STOP the engine will now stop.
2) Be aware that the cutting head may not stop immediately and allow it to
slow down fully.
STOP
(1)
(2)
THE NYLON CUTTING HEAD
During operation, use the tip of the nylon cutting cord for cut.
Feeding the nylon cutting cord
As the nylon cutting cord is worn and shortened with the cutting operation, the
operator needs to feed it manually.
To feed the nylon cutting cord, tap the nylon cutting head on the ground while it
rotates around 6,000 min
-1
.
NOTE: If the nylon cutting cord does not feed out, rewind it.
Most effective cutting area
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita ER2650LH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita ER2650LH in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita ER2650LH

Makita ER2650LH User Manual - English, German - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info