599894
18
Zoom out
Zoom in
Previous page
1/54
Next page
18
CAUTION: The cutting tools shown in the illustration are not to be sharpened.
Manual resharpening will result in imbalances of the cutting tool
causing vibrations and damage to the equipment.
NOTE: To increase the service life of the cutter blade it may be turned over
once, until both cutting edges have become blunt.
RESHARPENING THE CUTTING TOOL
ADJUSTMENT OF IDLE SPEED
When it is necessary to adjust the idle speed, perform it by the carburetor adjusting screw.
CHECKUP OF IDLE SPEED
Set the idle speed to 3,000 min
-1
.
If it is necessary to change the idle speed, use a phillips head screw driver on
the screw illustrated on the right.
To increase the idle speed, turn the adjusting screw clockwise.
To reduce the idle speed, turn the adjusting screw counterclockwise.
The carburetor is factory adjusted. However, after several use the idle speed
need to be re-adjusted.
NYLON CUTTING HEAD
The nylon cutting head is a dual line trimmer head that has bump & feed
mechanism.
The nylon cutting head will feed out the proper length of nylon line after tapping
the nylon cutting head on the ground by changes in centrifugal force caused by
increasing or decreasing rpms.
Operation
Increase the nylon cutting head speed to approx. 6,000 min
-1
.
Bump the nylon cutting head lightly on the ground.
The most effective cutting area is shown by the shaded area.
If the nylon cord does not feed out, rewind/replace the nylon cord by following
the procedures described under “Replacing the nylon cord.”
Most effective cutting area
STOPPING
1) Release the throttle lever (2) fully, and when the
engine rpm has lowered, set the I-O switch (1)
to STOP the engine will now stop.
2) The cutting tool continues to rotate a while
after stopping the engine. Wait until it stops
completely.
STOP
STOP
EM4350UH
EM4351UH
(1)
(2)
EM4350LH
(1)
(2)
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EM4350LH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EM4350LH in the language / languages: English, Dutch as an attachment in your email.

The manual is 9,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita EM4350LH

Makita EM4350LH User Manual - English, German - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info